LinHES Forums :: View topic - After upgrade : "Unable to initialize video"

LinHES Forums http://forum.linhes.org/

After upgrade : "Unable to initialize video" http://forum.linhes.org/viewtopic.php?f=11&t=4330	Page 1 of 1

Author:	adrianbc [ Thu Apr 28, 2005 7:19 pm ]
Post subject:	After upgrade : "Unable to initialize video"
I just upgraded to R5A15 from R5A12 . Since doing a mythrestore I am unable to watch TV or watch videos. Whenever I try to watch video or TV I get the myth background screen with the error "Unable to initialize video". I have tried to reinstall nvidia drivers (xvinfo looks fine). I have also gone through mythsetup. FYI my hardware is a Chaintech 7NIF2 with a PVR-250. here is my dmesg... Linux version 2.6.11.7-chw-3 (root@mbe.mysettopbox.tv) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 SMP Tue Apr 19 17:46:47 PDT 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001dff0000 (usable) BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS) BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 479MB LOWMEM available. On node 0 totalpages: 122864 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 118768 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.2 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f6ea0 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff7740 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:4 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 1e000000 (gap: 1e000000:e0c00000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=301 apm=power-off nomce mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1336.418 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 481460k/491456k available (3002k kernel code, 9444k reserved, 1138k data, 224k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 2646.01 BogoMIPS (lpj=1323008) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. CPU0: AMD Athlon(tm) processor stepping 04 per-CPU timeslice cutoff: 731.60 usecs. task migration cache decay timeout: 1 msecs. Total of 1 processors activated (2646.01 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=0 pin2=-1 Brought up 1 CPUs CPU0 attaching sched-domain: domain 0: span 0001 groups: 0001 domain 1: span 0001 groups: 0001 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 3k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050211 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: nForce2 C1 Halt Disconnect fixup ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) 0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16), disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17), disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18), disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19), disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 23), disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) 0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) 0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 16 devices PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI interrupts are no longer routed automatically. If this causes a device to stop working, it is probably because the driver failed to call pci_enable_device(). As a temporary workaround, the "pci=routeirq" argument restores the old behavior. If this argument makes the device work again, please email the output of "lspci" to bjorn.helgaas@hp.com ** so I can fix the driver. pnp: 00:00: ioport range 0x4000-0x407f could not be reserved pnp: 00:00: ioport range 0x4080-0x40ff has been reserved pnp: 00:00: ioport range 0x4400-0x447f has been reserved pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved pnp: 00:00: ioport range 0x4200-0x427f has been reserved pnp: 00:00: ioport range 0x4280-0x42ff has been reserved pnp: 00:01: ioport range 0x5000-0x503f has been reserved pnp: 00:01: ioport range 0x5100-0x513f has been reserved Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem Supermount version 2.0.8 for kernel 2.6 Initializing Cryptographic API isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE2: IDE controller at PCI slot 0000:00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: WDC WD2000JB-00GVA0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: MATSHITADVD-RAM LF-D310, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 1024KiB hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdc: ATAPI DVD-ROM DVD-R-RAM drive, 1024kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.10 loaded. Fusion MPT base driver 3.01.18 Copyright (c) 1999-2004 LSI Logic Corporation Fusion MPT SCSI Host driver 3.01.18 Fusion MPT misc device (ioctl) driver 3.01.18 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: PS/2 Generic Mouse on isa0060/serio1 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid10 personality registered as nr 9 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 2028.000 MB/sec 8regs_prefetch: 1808.000 MB/sec 32regs : 1284.000 MB/sec 32regs_prefetch: 1272.000 MB/sec pII_mmx : 3556.000 MB/sec p5_mmx : 4720.000 MB/sec raid5: using function: p5_mmx (4720.000 MB/sec) raid6: int32x1 511 MB/s raid6: int32x2 644 MB/s raid6: int32x4 382 MB/s raid6: int32x8 382 MB/s raid6: mmxx1 1121 MB/s raid6: mmxx2 1992 MB/s raid6: sse1x1 1070 MB/s raid6: sse1x2 1757 MB/s raid6: using algorithm sse1x2 (1757 MB/s) md: raid6 personality registered as nr 8 md: multipath personality registered as nr 7 md: faulty personality registered as nr 10 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 32Kbytes TCP established hash table entries: 16384 (order: 6, 262144 bytes) TCP bind hash table entries: 16384 (order: 5, 196608 bytes) TCP: Hash tables configured (established 16384 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 15 ACPI wakeup devices: SLPB HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1 ACPI: (supports S0 S1 S4 S5) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... <6>kjournald starting. Commit interval 5 seconds okay Freeing unused kernel memory: 224k freed Adding 891596k swap on /dev/hda2. Priority:-1 extents:1 EXT3 FS on hda1, internal journal usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 22 ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: irq 22, pci mem 0xce003000 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, high) -> IRQ 21 ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2) PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: irq 21, pci mem 0xce004000 ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' Real Time Clock Driver v1.12 ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Fan [FAN] (on) ACPI: Thermal Zone [THRM] (17 C) Linux Kernel Card Services options: [pci] [cardbus] [pm] Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected NVIDIA nForce2 chipset agpgart: Maximum main memory to use for agp memory: 409M agpgart: AGP aperture is 512M @ 0xa0000000 i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.31. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20 ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 20 (level, high) -> IRQ 20 PCI: Setting latency timer of device 0000:00:04.0 to 64 eth0: forcedeth.c: subsystem: 010de:0c11 bound to 0000:00:04.0 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22 ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 22 (level, high) -> IRQ 22 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 49852 usecs intel8x0: clocking to 47384 NET: Registered protocol family 17 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver kjournald starting. Commit interval 5 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. Disabled Privacy Extensions on device c04bcf80(lo) eth0: no link during initialization. eth0: link up. Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! lirc_dev: IR Remote Control driver registered, at major 61 Linux video capture interface: v1.00 bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture saa7115: starting probe for adapter SMBus nForce2 adapter at 5000 (0x0) saa7115: starting probe for adapter SMBus nForce2 adapter at 5100 (0x0) ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.2.0 (rc3i) loading ivtv: Linux version: 2.6.11.7-chw-3 SMP preempt 586 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 250 card ivtv: Found an iTVC16 based chip ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 ACPI: PCI interrupt 0000:01:06.0[A] -> GSI 16 (level, high) -> IRQ 16 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom,ok] ivtv: i2c attach [client=(tuner unset),ok] tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) msp34xx: ivtv version msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G) no-thread mode msp34xx: $Id$ compiled on: Apr 20 2005 06:45:08 ivtv: i2c attach [client=MSP3448W-A2,ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[0],ok] saa7115: status: (1E) 0x48, (1F) 0xc0 tveeprom: Hauppauge: model = 32032, rev = B310, serial# = 7043549 tveeprom: tuner = Philips FI1236 MK2 (idx = 10, type = 2) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3440 (type = 11) ivtv: Tuner Type 2, Tuner formats 0x00001000, Radio: yes, Model 0x00893450, Revision 0x00000001 ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 250 card with 5 streams ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Setting Tuner 2 tuner 2-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) saa7115: decoder set input (4) saa7115: now setting Composite input ivtv: Setting audio matrix to input 3, output 1 ivtv: Switching standard to NTSC. ivtv: ivtv_enc_thread: pid = 2014, itv = 0xdec37a20 saa7115: decoder set norm NTSC saa7115: set audio: 0x01 ivtv: Initialized WinTV PVR 250, card #0 ivtv: ==================== END INIT IVTV ==================== cx2388x v4l2 driver version 0.0.4 loaded lirc_i2c: chip found @ 0x18 (Hauppauge IR) ivtv: i2c attach [client=Hauppauge IR,ok] lirc_dev: lirc_register_plugin:sample_rate: 10 saa7115: decoder disable output saa7115: decoder set input (0) saa7115: now setting Composite input ivtv: Setting audio matrix to input 1, output 1 saa7115: decoder enable output saa7115: decoder set size eth0: no IPv6 routers present saa7115: decoder disable output saa7115: decoder set input (4) saa7115: now setting Composite input ivtv: Setting audio matrix to input 3, output 1 saa7115: decoder enable output saa7115: decoder disable output ts: Compaq touchscreen protocol output saa7115: decoder enable output input: PC Speaker saa7115: decoder set picture bright=128 contrast=63 saturation=64 hue=0 saa7115: decoder set picture bright=128 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 21 (level, high) -> IRQ 21 ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: irq 21, pci mem 0xce005000 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: park 0 ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, high) -> IRQ 16 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44:39 PST 2005 agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, high) -> IRQ 16 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44:39 PST 2005 agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode saa7115: decoder disable output saa7115: decoder enable output saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 saa7115: decoder set size saa7115: decoder disable output saa7115: decoder enable output

Author:	Quigs [ Sat Apr 30, 2005 6:12 am ]
Post subject:
I get this problem if I have xvmc checking in the tv settings under myth setup. It is a new setting on the PVR350 setup screen at the bottom. You might want to go in and check that.

Author:	Nnyan [ Tue May 03, 2005 1:59 am ]
Post subject:
where exactly do I find this? I'm having the same problem and now when i have the PVR connected to a monitor it gives me that error, I return to menu and it dumps me to desktop.

Author:	Xsecrets [ Tue May 03, 2005 8:09 am ]
Post subject:
it's under tv settings playback like the 4th or 5th screen use pvr350 is at the top of the screen followed by a very big empty box then at the very bottom below the box is the use xvmc checkbox.

Page 1 of 1	All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/