I decided I wanted to add tuner(s) to my single PVR-350 box, so I got a PVR500MCE to add to it. I've tried several versions of ivtv (currently using 0.4.0) and of the enc/dec binaries in /lib/modules, but all boil down the same basic problem. So, I was wondering if this sounded familiar to anyone. (or if there's any suggestions)
When I boot, I get the appended messages (I've also stuffed a WinTV GO Plus card in there in hopes that I can get SOMETHING to work right...so that's where the bttv stuff comes from, but my problems with the pvr500 are the same regardless).
This is an excerpt from my dmesg output related to the 1st tuner on the pvr500 card:
Code: ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
PCI: Enabling device 0000:02:08.0 (0014 -> 0016)
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 9 (level, low) -> IRQ 9
tveeprom: starting probe for adapter ivtv i2c driver #1 (0x10005)
ivtv1 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv1: Error -19 reading Hauppauge eeprom.
ivtv1: Possible causes: the tveeprom module was not loaded, or
ivtv1: the eeprom kernel module was loaded before the tveeprom module.
ivtv1 warning: i2c client addr: 0x44 not found for command 0x400464c9!
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1 warning: Encoder mailbox not found
ivtv1 warning: Decoder mailbox not found
ivtv1: Error locating firmware.
ivtv1: Error -12 on initialization
ivtv-iTVC15_16_mpg2_encoder_card: probe of 0000:02:08.0 failed with error -12
When I look at my PCI devices:
Code: mythtv% lspci | grep video
0000:01:00.0 Multimedia video controller: Internext Compression Inc iTVC15 MPEG-2 Encoder (rev 01)
0000:01:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:02:08.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
0000:02:09.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
(that's my PVR-350, WinTV GO Plus, then 2 tuners on the PVR-500MCE).
And I've gone through my /lib/modules dir, renaming any tveeprom & tuner files I've found to be sure that the only tveeprom.ko & tuner.ko are those from ivtv. Looking in /lib/modules, I have this:
Code: mythtv% ls -l
total 1084
drwxr-xr-x 11 root root 4096 Oct 29 23:34 2.6.11.9-chw-2
-r--r--r-- 1 root root 376836 Sep 3 20:45 HcwFalcn.rom
-r--r--r-- 1 root root 14264 Sep 3 20:45 HcwMakoA.ROM
drwxr-xr-x 3 root root 4096 Nov 20 2004 extra
-rw-r--r-- 1 root root 262144 Sep 3 23:57 ivtv-fw-dec.bin
lrwxrwxrwx 1 root root 25 Oct 9 19:13 ivtv-fw-enc.bin -> /lib/modules/HcwFalcn.rom
-rw-r--r-- 1 root root 262144 Sep 3 23:57 ivtv-fw-enc.bin-save
-rw-r--r-- 1 root root 155648 Oct 9 19:01 ivtv_init_mpeg.bin
drwxr-xr-x 2 root root 4096 Mar 22 2005 misc
drwxr-xr-x 2 root root 4096 Sep 3 20:45 save20050903
My /etc/mythtv/modules/ivtv file currently looks like this:
Code: alias char-major-81 videodev
alias char-major-61 lirc_i2c
options tveeprom debug=1
#
options cx25840 debug=1
#
options ivtv ivtv_debug=1
#
options saa7127 debug=1
#
options msp3400 once=1 simple=1
#
install ivtv /sbin/modprobe tuner; /sbin/modprobe msp3400; /sbin/modprobe saa7115; /sbin/modprobe --ignore-install ivtv; /sbin/modprobe --ignore-install ivtv-fb; /sbin/modprobe --ignore-install lirc_i2c
remove ivtv /sbin/modprobe -r --ignore-remove ivtv && /sbin/modprobe -r saa7115 && /sbin/modprobe -r msp3400 && /sbin/modprobe -r tuner && /sbin/modprobe -r ivtv-fb && /sbin/modprobe -r lirc_i2c
more complete dmesg output:
Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (iTVC15 based)
PCI: Enabling device 0000:01:00.0 (0014 -> 0016)
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
tveeprom: starting probe for adapter ivtv i2c driver #0 (0x10005)
tveeprom: detecting tveeprom client on address 0xa0
tveeprom: Tag [04] + 9 bytes:
tveeprom: 0x20
tveeprom: 0x77
tveeprom: 0x00
tveeprom: 0x40
tveeprom: 0xa5
tveeprom: 0x76
tveeprom: 0x2c
tveeprom: 0x00
tveeprom: Tag [05] + 3 bytes:
tveeprom: 0x9b
tveeprom: 0x00
tveeprom: Tag [06] + 8 bytes:
tveeprom: 0x04
tveeprom: 0xbc
tveeprom: 0x00
tveeprom: 0x00
tveeprom: 0x98
tveeprom: 0x25
tveeprom: 0xad
tveeprom: Tag [07] + 2 bytes:
tveeprom: 0x70
tveeprom: Not sure what to do with tag [07]
tveeprom: Tag [09] + 3 bytes:
tveeprom: 0x13
tveeprom: 0x5f
tveeprom: Tag [0a] + 3 bytes:
tveeprom: 0x08
tveeprom: 0x44
tveeprom: Tag [0b] + 3 bytes:
tveeprom: 0x59
tveeprom: 0x8c
tveeprom: Not sure what to do with tag [0b]
tveeprom: Tag [0e] + 2 bytes:
tveeprom: 0x01
tveeprom: Tag [0f] + 2 bytes:
tveeprom: 0x01
tveeprom: Not sure what to do with tag [0f]
tveeprom: Tag [10] + 2 bytes:
tveeprom: 0x01
tveeprom: Not sure what to do with tag [10]
tveeprom: Tag [11] + 2 bytes:
tveeprom: 0x00
tveeprom: Not sure what to do with tag [11]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 2913957
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G)
no-thread mode
msp34xx: $Id$ compiled on: Oct 9 2005 17:21:10
ivtv0: i2c attach to card #0 ok [client=MSP3448W-A2, addr=40]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
saa7127 debug 1-0044: detecting saa7127 client on address 0x88
saa7127 debug 1-0044: Configuring encoder
saa7127 debug 1-0044: Selecting NTSC video Standard
saa7127 debug 1-0044: Selecting S-Video + Composite output type
saa7127 debug 1-0044: Turn VPS Signal off
saa7127 debug 1-0044: Set VPS data 00 00 00 00 00
saa7127 debug 1-0044: CC disabled
saa7127 debug 1-0044: Turn WSS off
saa7127 debug 1-0044: WSS mode: 4:3 full format
saa7127 debug 1-0044: Selecting Normal Encoder Input
saa7127 debug 1-0044: Enable Video Output
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: loading /lib/modules/ivtv-fw-dec.bin
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loading /lib/modules/ivtv_init_mpeg.bin
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
PCI: Enabling device 0000:02:08.0 (0014 -> 0016)
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 9 (level, low) -> IRQ 9
tveeprom: starting probe for adapter ivtv i2c driver #1 (0x10005)
ivtv1 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv1: Error -19 reading Hauppauge eeprom.
ivtv1: Possible causes: the tveeprom module was not loaded, or
ivtv1: the eeprom kernel module was loaded before the tveeprom module.
ivtv1 warning: i2c client addr: 0x44 not found for command 0x400464c9!
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1 warning: Encoder mailbox not found
ivtv1 warning: Decoder mailbox not found
ivtv1: Error locating firmware.
ivtv1: Error -12 on initialization
ivtv-iTVC15_16_mpg2_encoder_card: probe of 0000:02:08.0 failed with error -12
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
PCI: Enabling device 0000:02:09.0 (0014 -> 0016)
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 5 (level, low) -> IRQ 5
tveeprom: starting probe for adapter ivtv i2c driver #1 (0x10005)
ivtv1 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv1: Error -19 reading Hauppauge eeprom.
ivtv1: Possible causes: the tveeprom module was not loaded, or
ivtv1: the eeprom kernel module was loaded before the tveeprom module.
ivtv1 warning: i2c client addr: 0x44 not found for command 0x400464c9!
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1 warning: Encoder mailbox not found
ivtv1 warning: Decoder mailbox not found
ivtv1: Error locating firmware.
ivtv1: Error -12 on initialization
ivtv-iTVC15_16_mpg2_encoder_card: probe of 0000:02:09.0 failed with error -12
ivtv: ==================== END INIT IVTV ====================
ivtv0-osd: Framebuffer module loaded (attached to ivtv card id 0)
ivtv0-osd warning: Framebuffer is at decoder-relative address 0x00510000 and has
1704960 bytes.
ivtv0-osd: screen coords: [0 0] -> [720 480]
ivtv0-osd: original global alpha = 208
ivtv0-osd: current OSD state = 39
ivtv0-osd: new global alpha = 208 (1 255 0)
ivtv0-osd: framebuffer at 0xe5510000, mapped to 0xe1990000, size 1350k
ivtv0-osd: mode is 720x480x32, linelength=2880
Console: switching to colour frame buffer device 90x30
ivtv0-osd: fb0: iTVC15 TV out frame buffer device
ivtv0: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total)
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Enabling device 0000:01:01.0 (0004 -> 0006)
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 5 (level, low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:01:01.0, irq: 5, latency: 132, mmio: 0xe8000000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom: starting probe for adapter bt878 #0 [sw] (0x10005)
tveeprom: detecting tveeprom client on address 0xa0
tveeprom: Tag [04] + 9 bytes:
tveeprom: 0x20
tveeprom: 0x77
tveeprom: 0x00
tveeprom: 0x40
tveeprom: 0xcb
tveeprom: 0x78
tveeprom: 0x7d
tveeprom: 0x00
tveeprom: Tag [05] + 3 bytes:
tveeprom: 0x00
tveeprom: 0x02
tveeprom: Tag [06] + 8 bytes:
tveeprom: 0xb5
tveeprom: 0xaf
tveeprom: 0x00
tveeprom: 0x00
tveeprom: 0x59
tveeprom: 0x16
tveeprom: 0x95
tveeprom: Tag [07] + 2 bytes:
tveeprom: 0x70
tveeprom: Not sure what to do with tag [07]
tveeprom: Tag [09] + 3 bytes:
tveeprom: 0x0e
tveeprom: 0x7f
tveeprom: Tag [0a] + 3 bytes:
tveeprom: 0x08
tveeprom: 0x63
tveeprom: Tag [0b] + 2 bytes:
tveeprom: 0x12
tveeprom: Not sure what to do with tag [0b]
tveeprom: Tag [0f] + 2 bytes:
tveeprom: 0x03
tveeprom: Not sure what to do with tag [0f]
tveeprom: Tag [10] + 2 bytes:
tveeprom: 0x01
tveeprom: Not sure what to do with tag [10]
tveeprom: Tag [11] + 2 bytes:
tveeprom: 0x00
tveeprom: Not sure what to do with tag [11]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 44981, rev = E199, serial# = 8222923
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = None (type = 0)
tveeprom: decoder processor = BT878 (type = e)
tuner (ivtv): chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tveeprom: tveeprom_read
tveeprom: Tag [04] + 9 bytes:
tveeprom: 0x20
tveeprom: 0x77
tveeprom: 0x00
tveeprom: 0x40
tveeprom: 0xcb
tveeprom: 0x78
tveeprom: 0x7d
tveeprom: 0x00
tveeprom: Tag [05] + 3 bytes:
tveeprom: 0x00
tveeprom: 0x02
tveeprom: Tag [06] + 8 bytes:
tveeprom: 0xb5
tveeprom: 0xaf
tveeprom: 0x00
tveeprom: 0x00
tveeprom: 0x59
tveeprom: 0x16
tveeprom: 0x95
tveeprom: Tag [07] + 2 bytes:
tveeprom: 0x70
tveeprom: Not sure what to do with tag [07]
tveeprom: Tag [09] + 3 bytes:
tveeprom: 0x0e
tveeprom: 0x7f
tveeprom: Tag [0a] + 3 bytes:
tveeprom: 0x08
tveeprom: 0x63
tveeprom: Tag [0b] + 2 bytes:
tveeprom: 0x12
tveeprom: Not sure what to do with tag [0b]
tveeprom: Tag [0f] + 2 bytes:
tveeprom: 0x03
tveeprom: Not sure what to do with tag [0f]
tveeprom: Tag [10] + 2 bytes:
tveeprom: 0x01
tveeprom: Not sure what to do with tag [10]
tveeprom: Tag [11] + 2 bytes:
tveeprom: 0x00
tveeprom: Not sure what to do with tag [11]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 44981, rev = E199, serial# = 8222923
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = None (type = 0)
tveeprom: decoder processor = BT878 (type = e)
bttv0: using tuner=50
tuner: type set to 50 (TCL 2002N) by bt878 #0 [sw]
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea632
0,tea6420,tda8425,pic16c54 (PV951),ta8874z
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bttv0: registered device video1
bttv0: registered device vbi1
bttv0: registered device radio1
bttv0: PLL: 28636363 => 35468950 .. ok
|
