I have installed Knoppmyth backend on an MSI RS480M2-IL motherboard with a PVR-250 capture card:
R5E50
API Library version: 20.200.20060828-3
source code: 12306M
the livecd media was verified prior to install
root@mythtv:~# uname -a
Linux mythtv 2.6.18-chw-13 #1 SMP PREEMPT Sun Dec 3 23:47:01 PST 2006 i686 GNU/Linux
root@mythtv:~# dmesg | egrep -i "ivtv|btt|vid}"
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.8.2 (tagged release) loading
ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-B3 found @ 0x80 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: Autodetected Hauppauge WinTV PVR-250
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
ivtv: ==================== END INIT IVTV ====================
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
lspci
[...]
02:00.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
[...]
but I'm getting frustrated during the post install, mythtv-setup process. Simply put, the "Input connections" section produces the following when I attempt to scan for channels on "Tuner 1":
Failed to open the card
Programmer Error, see console
When I go to tty1, I see nothing other than normal startup messages.
dmesg does have a number of "APIC error on CPU0" messages, but this doesn't seem be assocated with the inability to open the capture card device. In fact, I turned off APIC in the BIOS rebooted and re-attempted the post install setup and still got the same errors
I've looked through the board contributions/suggestions and tried the following:
- changing permissions (777) of the video devices
- restarting the post install mythtv-setup process
- verified that I'm using the right version of ivtvctl for the kernel version
- cat /dev/video0 > /tmp/test.mpg (wait 5 secs) ^c mplayer /tmp/test.mpg
(that works, in that I get static, which is what I would expect since I haven't been able to scan for channels)
- I even tried redoing the entire install process over gain using a spare bt878A card I had laying around (same results) and then again with a different motherboard (via EPIA C3)
I'm really at a loss here... I thought Knoppmyth was supposed to make things easy.
entire dmesg ouput follows:
root@mythtv:~# dmesg
Linux version 2.6.18-chw-13 (root@mythtv) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP PREEMPT Sun Dec 3 23:47:01 PST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
BIOS-e820: 000000001bef0000 - 000000001bef3000 (ACPI NVS)
BIOS-e820: 000000001bef3000 - 000000001bf00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
446MB LOWMEM available.
found SMP MP-table at 000f3dd0
On node 0 totalpages: 114416
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 110320 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 RS480 ) @ 0x000f7c30
ACPI: RSDT (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bef3040
ACPI: FADT (v002 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bef30c0
ACPI: MCFG (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bef6a80
ACPI: MADT (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bef69c0
ACPI: DSDT (v001 RS480 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1bf00000:c4100000)
Detected 1790.954 MHz processor.
Built 1 zonelists. Total pages: 114416
Kernel command line: auto BOOT_IMAGE=Linux ro root=301 apm=power-off nomce quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 446768k/457664k available (4291k kernel code, 10380k reserved, 1349k data, 268k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3583.89 BogoMIPS (lpj=1791949)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Total of 1 processors activated (3583.89 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 45k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 0:18
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 *10 11), disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 3 of device 0000:00:00.0
pnp: 00:01: ioport range 0x228-0x22f has been reserved
pnp: 00:01: ioport range 0x40b-0x40b has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: ioport range 0xc00-0xc01 has been reserved
pnp: 00:01: ioport range 0xc14-0xc14 has been reserved
pnp: 00:01: ioport range 0xc50-0xc52 has been reserved
pnp: 00:01: ioport range 0xc6c-0xc6d has been reserved
pnp: 00:01: ioport range 0xc6f-0xc6f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: fde00000-fdefffff
PREFETCH window: d8000000-dfffffff
PCI: Bridge: 0000:00:14.4
IO window: d000-dfff
MEM window: fdd00000-fddfffff
PREFETCH window: f8000000-fbffffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1173095145.468:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFS: nTxBlock = 3491, nTxLock = 27935
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
vesafb: framebuffer at 0xd8000000, mapped to 0xdca80000, using 6144k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:5260
vesafb: pmi: set display start = c00c52ce, set palette = c00c5308
vesafb: pmi: ports = ef10 ef16 ef54 ef38 ef3c ef5c ef00 ef04 efb0 efb2 efb4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4
Copyright (c) 1999-2006 Intel Corporation.
pcnet32.c:v1.32 18.Mar.2006
tsbogend@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 16
eth0: RealTek RTL8139 at 0xdc802000, 00:13:d3:04:8f:ba, IRQ 16
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker <becker@scyld.com>
URL:http://www.scyld.com/network/drivers.html
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf300-0xf307, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf308-0xf30f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: IC35L020AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-109, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/1863KiB Cache, CHS=38792/16/63
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v1.1-646.<7>libata version 2.00 loaded.
sata_sil 0000:00:11.0: version 2.0
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 18
ata1: SATA max UDMA/100 cmd 0xDC804080 ctl 0xDC80408A bmdma 0xDC804000 irq 18
ata2: SATA max UDMA/100 cmd 0xDC8040C0 ctl 0xDC8040CA bmdma 0xDC804008 irq 18
scsi0 : sata_sil
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 19
ata3: SATA max UDMA/100 cmd 0xDC806080 ctl 0xDC80608A bmdma 0xDC806000 irq 19
ata4: SATA max UDMA/100 cmd 0xDC8060C0 ctl 0xDC8060CA bmdma 0xDC806008 irq 19
scsi2 : sata_sil
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_sil
ata4: SATA link down (SStatus 0 SControl 300)
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 761 MB/s
raid6: int32x2 695 MB/s
raid6: int32x4 531 MB/s
raid6: int32x8 492 MB/s
raid6: mmxx1 1433 MB/s
raid6: mmxx2 2628 MB/s
input: AT Translated Set 2 keyboard as /class/input/input0
raid6: sse1x1 1328 MB/s
raid6: sse1x2 1722 MB/s
raid6: sse2x1 1839 MB/s
raid6: sse2x2 2675 MB/s
raid6: using algorithm sse2x2 (2675 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 5420.000 MB/sec
raid5: using function: pIII_sse (5420.000 MB/sec)
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@redhat.com
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
Suspend2 Core.
Suspend2 Userspace UI Support module loaded.
Suspend2 Userspace Storage Manager module loaded.
Suspend2 Compressor module loaded.
Suspend2 Encryptor module loaded.
Suspend2 Block I/O module loaded.
Suspend2 Swap Allocator module loaded.
ACPI: (supports S0 S1 S3 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
Time: tsc clocksource has been installed.
VFS: Mounted root (ext2 filesystem).
Suspend2 2.2.8.4: You need to use a resume2= command line parameter to tell Suspend2 where to look for an image.
Suspend2 2.2.8.4: Resume2 parameter is empty. Suspending will be disabled.
Suspend2 2.2.8.4: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending.
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
(fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recovered transactions 1081 to 2320
(fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 7395 and revoked 250/21 blocks
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 268k freed
ts: Compaq touchscreen protocol output
Linux video capture interface: v2.00
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fddfe000-fddfe7ff] Max Packet=[2048] IR/IT contexts=[4/8]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ivtv: ==================== START INIT IVTV ====================
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 20, io mem 0xfe02d000
ivtv: version 0.8.2 (tagged release) loading
ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
APIC error on CPU0: 00(40)
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 20, io mem 0xfe02c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 20
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: irq 20, io mem 0xfe02b000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 22
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 20 (level, low) -> IRQ 16
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000a124bc]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-B3 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-B3 supports radio, mode is autodetect and autoselect
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
tveeprom 1-0050: Hauppauge model 32032, rev B382, serial# 7261971
tveeprom 1-0050: tuner model is LG TAPC H791F (idx 82, type 39)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is MSP4448 (idx 27)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has no radio, has IR remote
ivtv0: Autodetected Hauppauge WinTV PVR-250
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
tuner 1-0061: type set to 39 (LG NTSC (newer TAPC series))
ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
ivtv: ==================== END INIT IVTV ====================
Adding 669304k swap on /dev/hda2. Priority:-1 extents:1 across:669304k
EXT3 FS on hda1, internal journal
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: AUDIO driver version 0.0.0 loaded
Non-volatile memory driver v1.2
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
root@mythtv:~#
View unanswered posts
View active topics
Linux 
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register
