| LinHES Forums http://forum.linhes.org/ |
|
| Linux DHCP problems ... http://forum.linhes.org/viewtopic.php?f=14&t=3941 |
Page 1 of 1 |
| Author: | riddlebox914 [ Thu Mar 24, 2005 8:36 am ] |
| Post subject: | Linux DHCP problems ... |
Hey everyone I just installed knoppmyth. I am a Linux newbie but no stranger to a computer. For some reason Linux fails when I try to obtain an IP address. So I set a static address (or how one web site told me how to set a static address) in /etc/network. I am trying to get knoppmyth to update weather, guides and such before I play with the TV end of it. Any help would be great! |
|
| Author: | riddlebox914 [ Thu Mar 24, 2005 12:18 pm ] |
| Post subject: | Update |
I know thats probally not enough info for a Linux expert but here is some more info I think might be useful ... When I type ifconfig all I was getting is "lo" information so I set a static IP on my internal network with the command ifconfig eth0 192.168.1.18 netmask 255.255.255.0 broadcast 192.168.1.255 But I still can not ping anything on my network or any internet site Although I can ping the loopback address (127.0.0.1) Hope this info helps |
|
| Author: | Xsecrets [ Thu Mar 24, 2005 1:00 pm ] |
| Post subject: | |
well just try running netcardconfig if it tells you it can't find a device then we need to know what NIC you are using so we can figure out what module to tell you to load so the device driver is available. note that this is not a standard problem, most NIC's are detected fine, but lots of wireless NIC's and some of the very new onboard (generally gigabit) NIC's aren't detected. |
|
| Author: | riddlebox914 [ Thu Mar 24, 2005 1:51 pm ] |
| Post subject: | Update |
Its an onboard NIC from a 1GHZ HP computer. But I also put in a Popular brand D-link and got the same responce so I took it back out. When I typed "netcardconfig" Here's what I got ... Sending DHCP broadcast from device eth0failed to connect to localhost:bootpc: Operation now in progress. There might be another pump running! Operation Failed Failed Hit re |
|
| Author: | riddlebox914 [ Mon Mar 28, 2005 8:45 am ] |
| Post subject: | More info ... |
When I type ifconfig all I get is "lo" I donno what this is but it is set up to 127.0.0.1 (loopback) I reconfigred this to a static IP on my network. I can ping internal addresses but nothing external. even when I configure eth0 it makes no differnce. The only time I can ping anything is when I reconfigure the lo, but I still can not get out to the internet. |
|
| Author: | Xsecrets [ Mon Mar 28, 2005 8:56 am ] |
| Post subject: | |
you should NEVER change lo it is your loopback address and you need it just like it is. You need to figure out what module your NIC is supposed to use and load that module then run netcardconfig again. not sure why this didn't happen on install for you, it's supposed to. |
|
| Author: | riddlebox914 [ Mon Mar 28, 2005 9:08 am ] |
| Post subject: | |
Ok thanks for the lo update .... I will reset it. I ran netcardconfig and it do not seem to obtain an ip address. It fails. I keep getting ... Sending DHCP broadcast from device eth0failed to connect to localhost:bootpc: Operation now in progress. There might be another pump running! Operation Failed Failed and when I set a static IP that works with my network .... I can ping local addresses and the gateway (which I also set) but no external public addresses or sites. Since I am dealing with an onboard NIC and nothing is working I am starting to think its a compatibly issue with the hardware. I am going to try running mythtv on another version of linux (any suggestions) and if that does not seem to work I am going to try knoppmyth on a new PC. |
|
| Author: | Xsecrets [ Mon Mar 28, 2005 9:11 am ] |
| Post subject: | |
If you had to use another version I would say FC3 so you could use the guide to install it. But be warned there are several people here who will vouch for the fact that even with the guides it's much more difficult to get working on another distro than knoppmyth. out of curiosity does your mb have firewire? |
|
| Author: | riddlebox914 [ Thu Mar 31, 2005 10:50 am ] |
| Post subject: | Got it working ... |
I resently changed all hardware to another box and it seemed to work perfectly. Had to be somthing with that box |
|
| Author: | SnapperDragon [ Thu Mar 31, 2005 11:25 am ] |
| Post subject: | |
Wold downloading a copy of the latest Knoppix help? I'm not sure how close to Knoppix KnoppMyth autodetection is, but if Knoppix boots up correctly and lets you access the net, then you know that all that needs to be done is figure out the module that was loaded for the nic. You may just have an unsupported nic. There seem to be a few new chipsets coming out lately and I find most of my problems iwth Linux is that the hardware is too new. |
|
| Author: | pedxing55 [ Mon Apr 11, 2005 1:26 am ] |
| Post subject: | |
hi, i've recently had the same exactly problem. when i installed knoppmyth the ethernet connection was working fine, but now when i startup it never recognizes the connection. any ideas? |
|
| Author: | pedxing55 [ Mon Apr 11, 2005 4:45 am ] |
| Post subject: | |
UPDATE: I did nothing, and it fixed itself...weird. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|