sorry with sound ..... if one isn't using the line in on the sound card ...
So status is a PVR 500 work after getting a replacement
)
| LinHES Forums http://forum.linhes.org/ |
|
| PVR 500 and knoppmyth installation http://forum.linhes.org/viewtopic.php?f=14&t=5403 |
Page 1 of 1 |
| Author: | Guest [ Tue Jul 19, 2005 9:01 am ] |
| Post subject: | PVR 500 and knoppmyth installation |
I just installed knoppmyth and followed pretty much these guides: http://www.bitbenderforums.com/~ralpha6 ... mythtv.htm http://mysettopbox.tv/phpBB2/viewtopic. ... ht=pvr+500 And i importet my channel list and added the frequencies from tdc in the channels ( Danish cabel operator ) but when i press "watch TV" only a black screen comes up .... anyone got an idea and are there any log-files i can post that be more help full than my noob talk ? ill be gratefull if any one could help |
|
| Author: | Guest [ Tue Jul 19, 2005 1:00 pm ] |
| Post subject: | |
never mind i think i found the problem I swapped the card to a windows machine and it keeps rebooting my system when i search for channels there and if i get a channel locked and is watching it the computer reboots after a short time ..... so i believe the card could be brooken so tomorrow ill try and swap it for a pvr 350 instead |
|
| Author: | brendan [ Wed Jul 20, 2005 2:10 pm ] |
| Post subject: | |
Does you motherboard have a via chipset? -brendan |
|
| Author: | Guest [ Wed Jul 20, 2005 2:34 pm ] |
| Post subject: | |
yep it's a as k7vt6 asrock I have now installed the pvr 500 with knoppmyth but still i can't see any picture when "watching live tv" but the card seems to work ok ...... but i can't figure what's wrong |
|
| Author: | tjc [ Wed Jul 20, 2005 5:16 pm ] |
| Post subject: | |
Certain older VIa chipsets had a DMA or IRQ problem with the PVR cards. I forget which... However a search for "via" and "ivtv" should turn up the details. |
|
| Author: | eleventy5 [ Mon Jul 25, 2005 7:28 pm ] |
| Post subject: | |
I am having the exact same problem (intel chipset) Everything in the dmesg output seems to point to a working PVR 500 (or 2 working pvr-150), But when I click live tv I get a black screen which also locks the machine up. I am unable to exit the black screen with any keyboard commands. I am attempting to use R5A16. Any help on this would be much appreciated. dmesg output Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (o) loading ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 22 (level, low) -> IRQ 22 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7893572 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Rev ision 0x00000000 ivtv: NTSC tuner detected ivtv: Radio detected cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 0 using 128 32768 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 using 194 10800 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 2 using 240 8736 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 cx25840: decoder set norm NTSC cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to NTSC. cx25840: decoder set norm NTSC ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 23 (level, low) -> IRQ 23 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7893572 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005) cx25840: starting probe for adapter ivtv i2c driver #1 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM ivtv: ivtv_enc_thread: pid = 2267, itv = 0xe1032820 ivtv: ivtv_enc_vbi_thread: pid = 2268, itv = 0xe1032820 cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Rev ision 0x00000000 ivtv: Radio detected eth0: no IPv6 routers present ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 0 using 128 32768 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 33 ivtv: Create DMA stream 1 using 194 10800 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create DMA stream 2 using 240 8736 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 25 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 65 ivtv: Create stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 cx25840: decoder set norm NTSC cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to NTSC. cx25840: decoder set norm NTSC ivtv: Initialized WinTV PVR 150, card #1 ivtv: ==================== END INIT IVTV ==================== |
|
| Author: | Guest [ Fri Jul 29, 2005 10:35 am ] |
| Post subject: | |
I have now update the bios with the latest release but nothing has changed i still got that black screen. I have passed the errors from mythbackend and dmesg if that can help ? I get the following error from mythtv backend when displaying live tv: Code: 2005-07-29 18:35:31.582 MainServer::HandleAnnounce Playback 2005-07-29 18:35:31.582 adding: mythtv as a client (events: 0) 2005-07-29 18:35:31.599 MainServer::HandleAnnounce Playback 2005-07-29 18:35:31.599 adding: mythtv as a client (events: 1) 2005-07-29 18:35:31.611 MainServer::HandleAnnounce Playback 2005-07-29 18:35:31.611 adding: mythtv as a client (events: 0) 2005-07-29 18:35:31.627 MainServer::HandleAnnounce Playback 2005-07-29 18:35:31.627 adding: mythtv as a client (events: 0) 2005-07-29 18:35:31.634 adding: mythtv as a remote ringbuffer 2005-07-29 18:35:31.644 Changing from None to WatchingLiveTV 2005-07-29 18:35:31.655 Can't enable VBI recording vbi: Invalid argument error reading from: /dev/video1 read: Input/output error error reading from: /dev/video1 read: Input/output error error reading from: /dev/video1 read: Input/output error error reading from: /dev/video1 read: Input/output error 2005-07-29 18:35:46.692 Couldn't read data from the capture card in 15 seconds. Stopping. 2005-07-29 18:35:46.723 Changing from WatchingLiveTV to None error reading from: /dev/video1 read: Input/output error dmesg displayes the following .... i can se there are som errors but i don't know how to fix them: Code: PnPBIOS: Found PnP BIOS installation structure at 0xc00f7ad0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x68ab, dseg 0xf0000 PnPBIOS: Missing SMALL_TAG_ENDDEP tag PnPBIOS: Missing SMALL_TAG_ENDDEP tag PnPBIOS: Missing SMALL_TAG_ENDDEP tag PnPBIOS: Missing SMALL_TAG_ENDDEP tag PnPBIOS: Missing SMALL_TAG_ENDDEP tag PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver SCSI subsystem initialized PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21 ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21 ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21 ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21 ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 17 (level, low) -> IRQ 17 Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem SELinux: Registering netfilter hooks Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5 PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5 vesafb: framebuffer at 0xc0000000, mapped to 0xe0880000, size 3072k vesafb: mode is 1024x768x16, linelength=2048, pages=0 vesafb: protected mode interface info at c000:0eb9 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.4-2004/02/19-spock-0.1: looking for picture... no good signature found. Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: Maxtor 6Y160P0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-ST CD-RW GCE-8240B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hda: max request size: 1024KiB hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63 hda: cache flushes supported hda: hda1 hda2 hda3 hda4 libata version 1.02 loaded. sata_via version 0.20 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20 sata_via(0000:00:0f.0): routed to hard irq line 10 ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD800 irq 20 ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD808 irq 20 ata1: no device found (phy stat 00000000) scsi0 : sata_via ata2: no device found (phy stat 00000000) scsi1 : sata_via mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 15 ACPI: (supports S0 S1 S4 S5) ACPI wakeup devices: PCI0 UAR1 USB1 USB2 USB3 USB4 EHCI USBD PS2M PS2K AC9 MC9 ILAN SLPB RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... <6>kjournald starting. Commit interval 5 seconds okay Freeing unused kernel memory: 196k freed Adding 787176k swap on /dev/hda2. Priority:-1 extents:1 EXT3 FS on hda1, internal journal hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache Uniform CD-ROM driver Revision: 3.20 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 21, io base 0000c000 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 21, io base 0000c400 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.2: irq 21, io base 0000c800 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 21, io base 0000cc00 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org> Real Time Clock Driver v1.12 ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1) Linux Kernel Card Services options: [pci] [cardbus] [pm] Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport: PnPBIOS parport detected. pnp: Device 00:0a disabled. Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected VIA KT400/KT400A/KT600 chipset agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 64M @ 0xe0000000 gameport: pci0000:00:0a.1 speed 1193 kHz via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23 eth0: VIA Rhine II at 0xdfffbd00, 00:0b:6a:6d:fb:1a, IRQ 23. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 4de1. ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18 NET: Registered protocol family 17 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver ttyS1: LSR safety check engaged! ttyS1: LSR safety check engaged! kjournald starting. Commit interval 5 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. Disabled Privacy Extensions on device c0465bc0(lo) eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1 Linux video capture interface: v1.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.6 (o) loading ivtv: Linux version: 2.6.9-chw-4 SMP preempt 586 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 16 (level, low) -> IRQ 16 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x3189 vendor: 0x1106 tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 2990138 tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56) tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 56, Tuner formats 0x00400e17, Radio: yes, Model 0x00915651, Revision 0x00000000 ivtv: PAL tuner detected ivtv: Radio detected tuner: Ignoring new-style parameters in presence of obsolete ones tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: Unknown parameter `no_black_magic' cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] tda9885/6/7: chip found @ 0x86 ivtv: i2c attach [client=tda9887,ok] ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 0 using 128 32768 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 using 161 12960 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 2 using 165 12635 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 cx25840: decoder set norm PAL cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to PAL. cx25840: decoder set norm PAL ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 17 (level, low) -> IRQ 17 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x3189 vendor: 0x1106 tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 2990138 tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56) tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe for adapter ivtv i2c driver #1 (0x10005) ivtv: i2c attach [client=wm8775[50],ok] tda9885/6/7: chip found @ 0x86 ivtv: i2c attach [client=tda9887,ok] ivtv: Tuner Type 56, Tuner formats 0x00400e17, Radio: yes, Model 0x00915651, Revision 0x00000000 ivtv: Radio detected ivtv: ivtv_enc_thread: pid = 2139, itv = 0xe0f07620 ivtv: ivtv_enc_vbi_thread: pid = 2140, itv = 0xe0f07620 ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 0 using 128 32768 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 33 ivtv: Create DMA stream 1 using 161 12960 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create DMA stream 2 using 165 12635 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 25 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 65 ivtv: Create stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: i2c client addr: 0x44 not found for command 1074029571! ivtv: i2c client addr: 0x44 not found for command 1074029572! ivtv: i2c client addr: 0x44 not found for command 1074029678! ivtv: Switching standard to PAL. ivtv: i2c client addr: 0x44 not found for command 1074029571! ivtv: Initialized WinTV PVR 150, card #1 ivtv: ==================== END INIT IVTV ==================== cx25840: decoder set size: ignoring bad config request Hsrc=720 Vsrc=487 width=720 height=576 ivtv: i2c client addr: 0x44 not found for command 1075864679! ivtv: ivtv_enc_thread: pid = 2203, itv = 0xe0f2a960 ivtv: ivtv_enc_vbi_thread: pid = 2204, itv = 0xe0f2a960 eth0: no IPv6 routers present ts: Compaq touchscreen protocol output input: PC Speaker cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21 ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: irq 21, pci mem e0d92e00 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004 agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Device is in legacy mode, falling back to 2.x agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 1075864679! ivtv: i2c client addr: 0x44 not found for command 1074029668! ivtv: Sliced VBI not supported for cx25840 so no vbi re-insertion possible yet ivtv: Allocate DMA stream 0 using 128 32768 byte buffers 4194304 kbytes total ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 1075864679! ivtv: i2c client addr: 0x44 not found for command 1074029668! ivtv: Sliced VBI not supported for cx25840 so no vbi re-insertion possible yet ivtv: Allocate DMA stream 0 using 128 32768 byte buffers 4194304 kbytes total ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 1074029670! ivtv: Setup VBI API header 0x0000bd0c pkts 1 buffs 48 ln 34 sz 64 ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 lines 0x00000140 ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: i2c client addr: 0x44 not found for command 1074029574! ivtv: Timeout waiting for data! Encoder buffers have 0x00000000 bytes trans_id = 0. ivtv: Check digitizer Sync ivtv: Resetting digitizer ivtv: i2c client addr: 0x44 not found for command 25701! ivtv: Failed reseting digitizer! ivtv: Capture has failed!!! Try again. ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 1074029574! tuner: TV freq (268370270.56) out of range (44-958) ivtv: i2c client addr: 0x44 not found for command 1074029574! cx25840: decoder set picture bright=128 contrast=63 saturation=64 hue=0 cx25840: decoder set picture bright=128 contrast=63 saturation=63 hue=0 cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder disable output tuner: TV freq (268370270.56) out of range (44-958) cx25840: decoder enable output cx25840: decoder set norm PAL cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 2150392936! ivtv: i2c client addr: 0x44 not found for command 1074684935! ivtv: i2c client addr: 0x44 not found for command 1074029574! tuner: TV freq (268370270.56) out of range (44-958) ivtv: i2c client addr: 0x44 not found for command 1074029574! cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder set picture bright=127 contrast=63 saturation=63 hue=0 cx25840: decoder disable output tuner: TV freq (268370270.56) out of range (44-958) cx25840: decoder enable output cx25840: decoder set norm PAL cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) |
|
| Author: | Xsecrets [ Fri Jul 29, 2005 11:21 am ] |
| Post subject: | |
the big thing I see is tveeprom is detecting tuner type 56 but you are setting the tuner type to 57. |
|
| Author: | Guest [ Sat Jul 30, 2005 12:03 pm ] |
| Post subject: | |
I tried to change the setting tuner=57,57 to tuner=56. One of the test i did run after this i could change between the channels but the only thing i could see was 3/4 of the screen was red and the bottom part were full of "noise" and it only happend 1 time after this i got the blackscreen which mythtv jumps out off after 10-30 sec |
|
| Author: | Guest [ Tue Aug 02, 2005 12:44 pm ] |
| Post subject: | |
I returned my pvr 500 card to the reseller who switched it. So i went home and plugged the card in my computer and startet without installing knoppmyth again. And now i can watch live tv ..... it still static but something is showing not a black screen so i believe it's my frequincy who is the problem now so ill do a tweak on them to see if it will work |
|
| Author: | Guest [ Tue Aug 02, 2005 2:46 pm ] |
| Post subject: | |
Now got picture with R5A12 when following this guide: http://www.bitbenderforums.com/~ralpha6 ... mythtv.htm But no sound yet but working on it |
|
| Author: | Guest [ Tue Aug 02, 2005 2:49 pm ] |
| Post subject: | |
sorry with sound ..... if one isn't using the line in on the sound card ...
So status is a PVR 500 work after getting a replacement )
|
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|