LinHES Forums http://forum.linhes.org/ |
|
Pioneer PDP 435 43" plasma and Mythtv http://forum.linhes.org/viewtopic.php?f=15&t=3871 |
Page 1 of 1 |
Author: | kellogs [ Sat Mar 19, 2005 6:41 am ] |
Post subject: | Pioneer PDP 435 43" plasma and Mythtv |
Hi Guys, I am using R5A10 with Geforce FX5200 and PVR 250. MythTV (DVI) ---> DVI 2 HDMI cable ---> Plasma HDMI I have installed the nvidia driver and now able to output to the plasma screen. After checking on the Xfree86log, i have noticed that it is using 640x480 resolution and the 4 corners on the plasma screen is not viewable. I am wondering if anyone has the same experience on setting up MythTV on a Plasma screen. Plasma specification Screen Size 43 Inches Aspect Ratio 16 : 9 Number of Pixels (Horizontal x Vertical) 1024 x 768 Brightness 1100 cd/m2 Contrast Ratio 1200 : 1 Viewing Angle More than 160 ° 3 Line Digital Comb Filter PAL/NTSC (Main & Sub) Video Signals PAL/SECAM/NTSC3.58/NTSC4.43/PAL-M/PAL-N/HD/PC PC Signals VGA/SVGA/XGA/Wide XGA Picture-in-Picture Display Yes Dual Screen Display Yes Still Picture Yes DNR (Digital Noise Reduction) Yes (Off/High/Mid/Low) MPEG NR Yes (Off/High/Mid/Low) Color Management Yes Natural Enhancer Yes Digital Flicker Fee Yes Digital CTI (Color Transient Improvement) Yes Dynamic Range Expander Yes (Off/High/Mid/Low) Color Temperature Adjustment Yes (High/Mid-High/Mid/Mid-Low/Low, Manual) PureCinema Yes (Off/Standard/ADV) AV Selection (Programmed Picture) Yes (STANDARD/DYNAMIC/MOVIE/GAME/USER) Reception System PAL B/G,I,D/K,M,N SECAM B/G, D/K NTSC M Stereo/ Dual Sound NICAM B/G, I D/K, CCIR A2 BG/DK, MTS Auto Search Yes Auto Channel Labeling Yes Auto Channel Sort Yes Number of Programmable Channels 125 Teletext CEEFAX/FLOF/TOP (with TOP Over View Page) Number of Languages 25 Page Memory 2,100 pages Picture and Text (Dual Screen) Yes OSD High-Quality Font Languages English, Chinese (Traditional), Chinese (Simple), Spanish, Portuguese Remote Controller SR Energy Save Mode (for AV and PC) Yes (Standard/Save) No Signal Off (for AV) Yes(Disable/Enable) No Operation Off (for AV) Yes(Disable/Enable) Power Management (for PC) Yes (Off/Mode1/Mode2) Audio Output Power 13 W + 13 W (1kHz, 10%, 8 ohms) Tone Control Bass, Treble, Balance Surround SRS* Audio Orientation FOCUS Bass Boost TruBass* Input1 AV Input, S-Video Input, Y/PB/PR Input Input2 AV Input, S-Video Input Input3 AV Input, S-Video Input, Y/PB/PR Input, HDMI Input Monitor Out (RCA pin) AV Out, S-Video Output Input 4(front) AV Input, S-Video Input PC (Front) D-sub 15 Input, Stereo Mini Jack Input (Audio) SR Control In/Out Mini Jack x 2 Others Antenna Terminal (DIN) System Connection x 2 (for plasma TV screen and media receiver) Speaker Out L/R (Display Rear, 8- 16 ohms) Display 1120 x 652 x 100 mm Media Receiver 420 x 90 x 297 mm Display 26.8 kg Media Receiver 5 kg Display 298 W (Standby Mode - 0.4W) Media Receiver 35W (Standby Mode - 0.4W) Total 333W (Standby Mode 0.8W) Power Requirement AC 110-240 V, 50/60 Hz Thanks! |
Author: | Liv2Cod [ Sun Mar 20, 2005 10:42 am ] |
Post subject: | |
You need to choose the right modeline to make your display useable. Your spec says the resolution is 1024x768. I don't believe that number, as it would mean your plasma display is not 16:9 but "normal" 4:3 ratio. I'd expect it to be more like 1280x768. Find out the right resolution, then read the Wiki on the subject of determining a modeline for your display. Here's the releveant Wiki page: HDTVSetupHowTo |
Author: | kellogs [ Sun Mar 20, 2005 1:20 pm ] |
Post subject: | |
Maybe i should go with powerstrip route ... Thanks for the info |
Author: | kellogs [ Sun Mar 20, 2005 1:22 pm ] |
Post subject: | |
I have the following input signal correlation table 1920*1080i@50Hz 720*576p@50Hz 1280*720p@50Hz 720(1440)*576i@50Hz 1920*1080i@59.94/60Hz 720*480p@59.94/60Hz 1280*720@59.94/60Hz 720(1440)*480i@59.94/60Hz |
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |