LinHES Forums http://forum.linhes.org/ |
|
Mythtv stops why and bad picture quality? http://forum.linhes.org/viewtopic.php?f=17&t=15309 |
Page 1 of 1 |
Author: | cando [ Mon May 21, 2007 5:15 pm ] |
Post subject: | Mythtv stops why and bad picture quality? |
When I am watching live tv mythtv just exits after one hour of watching. I have no idea why thats happening. Is it a configuration problem or my myth box ? I have got a nvidia 5200. A hauppauge pvr 150...(actually I bought a hauppauge pvr 250 off ebay.. that’s what it said there... but when I was configuring remote while installation of myth frontend I had to select option d which said "d. PVR-150 w/ transmitter and receiver" coz when I choose "b. Grey remote" my remote was not fully mapped... any idea which PVR I have got???) I have installed R5E50. Also is there a way to increase the quality of the picture. the picture is a little blurry. the picture quality of the live TV is a little depreciated as compared to what my settop box when connected directly to TV is giving. Any tweaking I could possibly do? Is it in the capture setting? In the recording settings of the following * Default * Live TV * Low Quality * High Quality I have all of these 4 options setup the highest resolution of I think 720x480. Is it the pvr-150 card which is bad? I would greatly appreciate any comment/suggestion/help |
Author: | tjc [ Mon May 21, 2007 5:36 pm ] |
Post subject: | |
http://www.knoppmythwiki.org/index.php?page=PictureQualityIssues BTW - You really should search before posting. This is another FAQ that comes up regulalrly. E.g. - http://mysettopbox.tv/phpBB2/viewtopic.php?t=13782&highlight=picture+quality |
Author: | cando [ Wed May 23, 2007 1:34 pm ] |
Post subject: | |
I am sorry if I am bothering you but am a little anxious... What about my other question? When I am watching live tv mythtv just exits after one hour of watching. I have no idea why thats happening. Is it a configuration problem or my myth box ? I have got a nvidia 5200. A hauppauge pvr 150...(actually I bought a hauppauge pvr 250 off ebay.. that’s what it said there... but when I was configuring remote while installation of myth frontend I had to select option d which said "d. PVR-150 w/ transmitter and receiver" coz when I choose "b. Grey remote" my remote was not fully mapped... any idea which PVR I have got???) I have installed R5E50. |
Author: | bruce_s01 [ Wed May 23, 2007 3:12 pm ] |
Post subject: | |
Does it stop with this error: "Error Was encountered while displaying video"? This is discussed in this thread. It seems to be a problem that appears for some people. Bruce S. |
Author: | tjc [ Wed May 23, 2007 6:18 pm ] |
Post subject: | |
What bruce_s01 said. I'd also recommend upgrading to R5F1 since there are more fixes for this issue in the MythTV 0.20-fixes branch between the version used in R5E50 and the one used in R5F1. |
Author: | cando [ Thu May 24, 2007 9:32 am ] |
Post subject: | |
I will check for Error Was encountered while displaying video error next time it happens. Some times the box shuts down is that a different overheating case? Upgrading to R5F1? isint that an older version of knoppmyth? |
Author: | slowtolearn [ Thu May 24, 2007 9:56 am ] |
Post subject: | |
cando wrote: I will check for Error Was encountered while displaying video error next time it happens. Some times the box shuts down is that a different overheating case? Very good possibility. Open up the case, clear out all the dust bunnies and see if that helps. Make sure your fans are spinning...cando wrote: Upgrading to R5F1? isint that an older version of knoppmyth? No, R5F1 was just released on May 11th -
http://mysettopbox.tv/ http://mysettopbox.tv/phpBB2/viewtopic.php?t=13537 |
Author: | cando [ Mon May 28, 2007 10:40 am ] |
Post subject: | |
Thanks slowtolearn! I cleaned the box. But the problem is that only the front end goes down. Then, I have to type Code: mythfrontend to get it back up again.
|
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |