| LinHES Forums http://forum.linhes.org/ |
|
| R5E50 --> R5F1 intially a black screen after reboot. http://forum.linhes.org/viewtopic.php?f=17&t=15477 |
Page 1 of 1 |
| Author: | glennph93 [ Sun Jun 03, 2007 1:55 pm ] |
| Post subject: | R5E50 --> R5F1 intially a black screen after reboot. |
Hi, I've read the Known issues section of R5F1 hints and hazards. This issue doesn't seem to apply since I'm upgrading from R5E50. When myth first boots and I go to watchtv it has sound but no picture, when I exit and go back to watchtv the picture is there. Another thing once it went to static after watching for awhile(reboot fixed). Its a pvr-150 card, a7n266-e board, mx4000 video card, and 768mb ram. Dmesg seems to have correct card: Code: Jun 3 14:57:11 mythtv kernel: ivtv: ==================== START INIT IVTV ====================
Jun 3 14:57:11 mythtv kernel: ivtv: version 0.10.1 (tagged release) loading Jun 3 14:57:11 mythtv kernel: ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1 Jun 3 14:57:11 mythtv kernel: ivtv: In case of problems please include the debug info between Jun 3 14:57:11 mythtv kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Jun 3 14:57:11 mythtv kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Jun 3 14:57:11 mythtv kernel: ivtv0: Autodetected Hauppauge card (cx23416 based) Jun 3 14:57:11 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) Jun 3 14:57:11 mythtv kernel: ivtv0: Encoder revision: 0x02060039 Jun 3 14:57:11 mythtv kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Jun 3 14:57:11 mythtv kernel: ivtv0: Autodetected Hauppauge WinTV PVR-150 Jun 3 14:57:11 mythtv kernel: ivtv0: reopen i2c bus for IR-blaster support Jun 3 14:57:11 mythtv kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Jun 3 14:57:11 mythtv kernel: cx25840 1-0044: cx25841-24 found @ 0x88 (ivtv i2c driver #0) Jun 3 14:57:11 mythtv kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) Jun 3 14:57:11 mythtv kernel: ivtv0: Registered device video0 for encoder MPEG (4 MB) Jun 3 14:57:11 mythtv kernel: ivtv0: Registered device video32 for encoder YUV (2 MB) Jun 3 14:57:11 mythtv kernel: ivtv0: Registered device vbi0 for encoder VBI (1 MB) Jun 3 14:57:11 mythtv kernel: ivtv0: Registered device video24 for encoder PCM audio (1 MB) Jun 3 14:57:11 mythtv kernel: ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 Jun 3 14:57:11 mythtv kernel: ivtv: ==================== END INIT IVTV ================ Thanks in advance |
|
| Author: | tjc [ Sun Jun 03, 2007 7:08 pm ] |
| Post subject: | |
Where's the rest of it? You must have done "grep ivtv" because you're missing all the tveeprom data. See the sed command on this page: http://www.knoppmythwiki.org/index.php?page=CheckingLogFiles The new drivers used in R5F1 require new firmware which means you need to shut the machine down cold and leave it off long enough (1-2 minutes is usually plenty) for the card to fully clear. |
|
| Author: | glennph93 [ Mon Jun 04, 2007 2:05 pm ] |
| Post subject: | |
tjc wrote: The new drivers used in R5F1 require new firmware which means you need to shut the machine down cold and leave it off long enough (1-2 minutes is usually plenty) for the card to fully clear.
Yep that solved my problem. Here is a more complete log: (although my problem is solved) Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.1 (tagged release) loading ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKD] -> GSI 18 (level, high) -> IRQ 16 ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) tveeprom 1-0050: Hauppauge model 26132, rev F1B2, serial# 9851208 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR receiver, has IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-150 ivtv0: reopen i2c bus for IR-blaster support tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-24 found @ 0x88 (ivtv i2c driver #0) Vendor: Sony Model: Storage Media Rev: 3.04 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sda: 127840 512-byte hdwr sectors (65 MB) sda: Write Protect is off sda: Mode Sense: 45 00 00 08 sda: assuming drive cache: write through SCSI device sda: 127840 512-byte hdwr sectors (65 MB) sda: Write Protect is off sda: Mode Sense: 45 00 00 08 sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda usb-storage: device scan complete cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) tuner 1-0061: type set to 50 (TCL 2002N) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== Thanks again for another great version of Knoppmyth and for the help. |
|
| Author: | tjc [ Mon Jun 04, 2007 7:34 pm ] |
| Post subject: | |
I've added a note about this to the known IVTV changes. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|