Author |
Message |
averagejoe
|
Posted: Wed Jan 19, 2011 10:47 am |
|
Joined: Fri Dec 31, 2010 9:43 am
Posts: 14
|
I am not sure where to begin on this. So far, except for some unexplained frontend crashes (usually at the end of a recording), MythTV on LinHES is good.
I have worked out all major technical hurdles with tuner, IR blaster, Hulu Desktop and more. I am down to the little stuff now. Stuff that has been a bit harder to find info on.
I am using a PVR-350 which unfortunately does not have a separate video in. I must use the analog tuner for both the DTV from the Zenith FTT910 and analog passthrough for about 3 analog channels that I would like to receive.
I preset the channel in setup to 3 and it sits there ready for any DTV coming from the STB. However, it stays on 3 when I try to change to the analog channels, though it changes the channel on the STB. I need the PVR-350 tuner to change to the channel I want. In the channel settings all the DTV channels have no channel entered for frequency, but the analog do. Apparently that setting will not override the channel 3 preset.
The STB channel change is fine, it doesn't matter what it is on for I am using the analog passthrough feature at that point. Where do I overide that preset? Or, must I remove that preset and manually enter 3 for every digital channel from the STB and the real channel for the 3 or 4 analog channels I want.
I am seeking advice to do it correctly and not need to experiment and change all my channel settings over and over. The channel setup is not horrible for a channel or two, but with over 50 channels to configure it is not exactly fun to edit them all.
|
|
Top |
|
|
tjc
|
Posted: Wed Jan 19, 2011 8:43 pm |
|
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location:
Arlington, MA
|
This should be a pretty simple SQL update statement... Is there any obvious way to identify the channels that use the STB?
|
|
Top |
|
|
averagejoe
|
Posted: Wed Jan 19, 2011 9:14 pm |
|
Joined: Fri Dec 31, 2010 9:43 am
Posts: 14
|
Seems like you are suggesting I disable the channel preset.and change all the channels to 3 except for the few analog ones.
I made all my channel numbers in the format of (channelnumber zero subchannel) since my remote has no dash. So channel 4-1 is 401 and channel 36-6 is 3606.
That means only analog channels have values under 100.
I need to learn more about SQL before I try anything fancy.
What I need then is for all channel numbers over 100, make their frequency = 3.
Is there a good resource with the mythtv database defined? I think I will need that at some point.
|
|
Top |
|
|
averagejoe
|
Posted: Wed Jan 19, 2011 10:47 pm |
|
Joined: Fri Dec 31, 2010 9:43 am
Posts: 14
|
I tested removing the channel preset. I have no idea how that should work. I still could not make the tuner switch to the analog channels. Plus if the freq is wrong my blaster fails to change the channel correctly.
I am not sure it is worth the effort for 1 real channel. There are 3 I could add, but 1 is spanish and another religious. Nothing wrong with those others, but I will not use them.
Or I can wait until I get my new antennas, HDHomerun and break out the PVR-350 as the analog tuner. I think if I can have that tuner scan, I could change to the channels they find.
I just wish I could make it work as is. I would like to use my STB as the 3rd tuner for Live TV when recording other shows. I hope to have the HDHomerun to augment my current setup. I hate it to be only to swap out the current tuner setup.
|
|
Top |
|
|