View unanswered posts    View active topics

Board index KnoppMyth Hardware

All times are UTC - 6 hours





Post new topic Reply to topic  Page 1 of 1
  [ 3 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
ryanpatterson
PostPosted: Thu Sep 01, 2005 8:10 pm 
Offline
Joined: Fri Aug 26, 2005 9:54 pm
Posts: 617
I had the pvr-500 installed and working. Then I added the pvr-350 now I have picture on the tuners on both cards. But the two tuners on the pvr-500 don't get any sound. They had sound before the pvr-350 was installed.

I am using ivtv-0.3.7k for my ivtv driver. I installed the firmware files for ivtv to /lib/modules The firmware files I put there are: HcwMakoA.ROM, ivtv-fw-dec.bin, ivtv-fw-enc.bin.

here is the ivtv output from dmesg:
Code:
Sep  1 21:52:23 mythtv kernel: ivtv: ==================== START INIT IVTV ====================
Sep  1 21:52:23 mythtv kernel: ivtv: version 0.3.7 (k) loading
Sep  1 21:52:23 mythtv kernel: ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3
Sep  1 21:52:23 mythtv kernel: ivtv: In case of problems please include the debug info
Sep  1 21:52:23 mythtv kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Sep  1 21:52:23 mythtv kernel: ivtv: mailing the ivtv-devel mailinglist.
Sep  1 21:52:23 mythtv kernel: ivtv: Autodetected WinTV PVR 350 card (iTVC15 based)
Sep  1 21:52:23 mythtv kernel: ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 17 (level, low) -> IRQ 17
Sep  1 21:52:23 mythtv kernel: tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 8229908
Sep  1 21:52:23 mythtv kernel: tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
Sep  1 21:52:23 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Sep  1 21:52:23 mythtv kernel: tveeprom: audio processor = MSP4448 (type = 1b)
Sep  1 21:52:23 mythtv kernel: tveeprom: decoder processor = SAA7115 (type = 13)
Sep  1 21:52:23 mythtv kernel: ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50]
Sep  1 21:52:23 mythtv kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Sep  1 21:52:23 mythtv kernel: ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61]
Sep  1 21:52:24 mythtv kernel: ivtv: i2c attach to card #0 ok [client=saa7115[50], addr=21]
Sep  1 21:52:24 mythtv kernel: ivtv: i2c attach to card #0 ok [client=saa7127[50], addr=44]
Sep  1 21:52:25 mythtv kernel: ivtv: Encoder revision: 0x02040011
Sep  1 21:52:25 mythtv kernel: ivtv: Decoder revision: 0x02020023
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create encoder radio stream
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create decoder VOUT stream
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total)
Sep  1 21:52:25 mythtv kernel: tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x40086d11!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x80287610!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x40287611!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x40307603!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x80287610!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x40287611!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x4004760f!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x80287610!
Sep  1 21:52:25 mythtv kernel: ivtv warning: i2c client addr: 0x40 not found for command 0x40287611!
Sep  1 21:52:25 mythtv kernel: ivtv: Initialized WinTV PVR 350, card #0
Sep  1 21:52:25 mythtv kernel: ivtv: ======================  NEXT CARD  ======================
Sep  1 21:52:25 mythtv kernel: ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
Sep  1 21:52:25 mythtv kernel: ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 21 (level, low) -> IRQ 21
Sep  1 21:52:25 mythtv kernel: tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 2994842
Sep  1 21:52:25 mythtv kernel: tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
Sep  1 21:52:25 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Sep  1 21:52:25 mythtv kernel: tveeprom: audio processor = CX25843 (type = 25)
Sep  1 21:52:25 mythtv kernel: tveeprom: decoder processor = CX25843 (type = 1e)
Sep  1 21:52:25 mythtv kernel: ivtv: i2c attach to card #1 ok [client=tveeprom[50], addr=50]
Sep  1 21:52:25 mythtv kernel: tuner: chip found at addr 0xc0 i2c-bus ivtv i2c driver #1
Sep  1 21:52:25 mythtv kernel: TEA5767 detected.
Sep  1 21:52:25 mythtv kernel: ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=60]
Sep  1 21:52:25 mythtv kernel: tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect
Sep  1 21:52:25 mythtv kernel: type set to 62 (Philips TEA5767HN FM Radio)
Sep  1 21:52:25 mythtv kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
Sep  1 21:52:25 mythtv kernel: ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=61]
Sep  1 21:52:25 mythtv kernel: ivtv: This is the first unit of a PVR500
Sep  1 21:52:26 mythtv kernel: cx25840: firmware /lib/modules/HcwMakoA.ROM loaded
Sep  1 21:52:26 mythtv kernel: ivtv: i2c attach to card #1 ok [client=cx25840[50], addr=44]
Sep  1 21:52:27 mythtv kernel: ivtv: i2c attach to card #1 ok [client=wm8775[50], addr=1b]
Sep  1 21:52:27 mythtv kernel: ivtv: Detected a TEA5767 radio tuner. Enabling radio support.
Sep  1 21:52:28 mythtv kernel: ivtv: Encoder revision: 0x02040011
Sep  1 21:52:28 mythtv kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Sep  1 21:52:28 mythtv kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Sep  1 21:52:28 mythtv kernel: ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
Sep  1 21:52:28 mythtv kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Sep  1 21:52:28 mythtv kernel: ivtv: Create encoder radio stream
Sep  1 21:52:28 mythtv kernel: tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1
Sep  1 21:52:29 mythtv kernel: ivtv: Initialized WinTV PVR 150, card #1
Sep  1 21:52:29 mythtv kernel: ivtv: ======================  NEXT CARD  ======================
Sep  1 21:52:29 mythtv kernel: ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
Sep  1 21:52:29 mythtv kernel: ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 22 (level, low) -> IRQ 22
Sep  1 21:52:29 mythtv kernel: tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 2994842
Sep  1 21:52:29 mythtv kernel: tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
Sep  1 21:52:29 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Sep  1 21:52:29 mythtv kernel: tveeprom: audio processor = CX25843 (type = 25)
Sep  1 21:52:29 mythtv kernel: tveeprom: decoder processor = CX25843 (type = 1e)
Sep  1 21:52:29 mythtv kernel: ivtv: i2c attach to card #2 ok [client=tveeprom[50], addr=50]
Sep  1 21:52:29 mythtv kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #2
Sep  1 21:52:29 mythtv kernel: ivtv: i2c attach to card #2 ok [client=(tuner unset), addr=61]
Sep  1 21:52:29 mythtv kernel: cx25840: firmware /lib/modules/HcwMakoA.ROM loaded
Sep  1 21:52:29 mythtv kernel: ivtv: i2c attach to card #2 ok [client=cx25840[50], addr=44]
Sep  1 21:52:29 mythtv kernel: ivtv: i2c attach to card #2 ok [client=wm8775[50], addr=1b]
Sep  1 21:52:29 mythtv kernel: ivtv: This is the second unit of a PVR500
Sep  1 21:52:29 mythtv kernel: ivtv: Correcting tveeprom data: no radio present on second tuner
Sep  1 21:52:30 mythtv kernel: ivtv: Encoder revision: 0x02040011
Sep  1 21:52:30 mythtv kernel: ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
Sep  1 21:52:30 mythtv kernel: ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
Sep  1 21:52:30 mythtv kernel: ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
Sep  1 21:52:30 mythtv kernel: ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
Sep  1 21:52:30 mythtv kernel: tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #2
Sep  1 21:52:31 mythtv kernel: ivtv: Initialized WinTV PVR 150, card #2
Sep  1 21:52:31 mythtv kernel: ivtv: ====================  END INIT IVTV  ====================


Everything there looks good to me.

I had "options tuner type=47,57,57" in my ivtv file. But I gave errors when initialising the pvr-500 (it wanted to use 47 not 57). So it is commented out. The auto detection seems to be working anyway.
Top
 Profile  
 
ryanpatterson
 Post subject:
PostPosted: Thu Sep 01, 2005 8:18 pm 
Offline
Joined: Fri Aug 26, 2005 9:54 pm
Posts: 617
update:

I just did a sanity check. The tuner with working audio is on the pvr-500. The pvr-350 tuner and the second pvr-500 tuner have no sound.
Top
 Profile  
 
wanttoknow
 Post subject:
PostPosted: Tue Jun 13, 2006 6:33 am 
Offline
Joined: Tue Oct 25, 2005 1:22 pm
Posts: 108
Location: USA, New Hampshire
ever found out what was the problem? I have 2 pvr-350's one with no soud though.. With R5C7

Thanks

_________________
Once you go HDTV, you'll never come back!
Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 3 posts ] 


Board index KnoppMyth Hardware

All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 24 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu