LinHES Forums :: View topic - any luck getting pvr150 built in irblaster working?

Reposting because I didn't want to hijack another persons post.

The receiver and blaster on a pvr150 are not working for me. Irrecord spits out a message of "hardware not found".

My /var/log/kern.log has the same message when lirc tries to load.

Quote:
Jun 6 10:00:21 mythtv kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jun 6 10:00:21 mythtv kernel: ivtv: ==================== START INIT IVTV ====================
Jun 6 10:00:21 mythtv kernel: ivtv: version 0.4.4 (tagged release) loading
Jun 6 10:00:21 mythtv kernel: ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3
Jun 6 10:00:21 mythtv kernel: ivtv: In case of problems please include the debug info between
Jun 6 10:00:21 mythtv kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with
Jun 6 10:00:21 mythtv kernel: ivtv: any module options, when mailing the ivtv-users mailinglist.
Jun 6 10:00:21 mythtv kernel: ivtv0: Autodetected WinTV PVR 250 card (cx23416 based)
Jun 6 10:00:21 mythtv kernel: ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 19
Jun 6 10:00:21 mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
Jun 6 10:00:21 mythtv kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
Jun 6 10:00:21 mythtv kernel: cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
Jun 6 10:00:24 mythtv kernel: cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
Jun 6 10:00:24 mythtv kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: Hauppauge model 26032, rev C199, serial# 8328268
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: audio processor is CX25841 (idx 35)
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: decoder processor is CX25841 (idx 2Cool
Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: has no radio, has IR remote
Jun 6 10:00:25 mythtv kernel: ivtv0: Corrected autodetection from WinTV PVR 250 to WinTV PVR 150
Jun 6 10:00:25 mythtv kernel: eth0: no IPv6 routers present
Jun 6 10:00:25 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
Jun 6 10:00:26 mythtv kernel: ivtv0: Encoder revision: 0x02050032
Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
Jun 6 10:00:26 mythtv kernel: tuner 1-0061: type set to 50 (TCL 2002N)
Jun 6 10:00:26 mythtv kernel: ivtv0: Initialized WinTV PVR 150, card #0
Jun 6 10:00:26 mythtv kernel: ivtv: ==================== END INIT IVTV ====================
Jun 6 10:00:26 mythtv kernel: lirc_pvr150: ivtv i2c driver #0: no devices found

Does this seem to be a IVTV problem or a LIRC problem? If someone has been able to get this to work could the let me kknow what version of the drivers they ended up using. I guess my next step would be to go to an older version if IVTV and/or LIRC but before I do that I would like to know if others have had any success.

Craig

Author:	iscraigh [ Tue Jun 06, 2006 5:54 pm ]
Post subject:	any luck getting pvr150 built in irblaster working?
Reposting because I didn't want to hijack another persons post. The receiver and blaster on a pvr150 are not working for me. Irrecord spits out a message of "hardware not found". My /var/log/kern.log has the same message when lirc tries to load. Quote: Jun 6 10:00:21 mythtv kernel: lirc_dev: IR Remote Control driver registered, at major 61 Jun 6 10:00:21 mythtv kernel: ivtv: ==================== START INIT IVTV ==================== Jun 6 10:00:21 mythtv kernel: ivtv: version 0.4.4 (tagged release) loading Jun 6 10:00:21 mythtv kernel: ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3 Jun 6 10:00:21 mythtv kernel: ivtv: In case of problems please include the debug info between Jun 6 10:00:21 mythtv kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Jun 6 10:00:21 mythtv kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Jun 6 10:00:21 mythtv kernel: ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) Jun 6 10:00:21 mythtv kernel: ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 19 Jun 6 10:00:21 mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32) Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] Jun 6 10:00:21 mythtv kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] Jun 6 10:00:21 mythtv kernel: cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) Jun 6 10:00:24 mythtv kernel: cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes) Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] Jun 6 10:00:24 mythtv kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: Hauppauge model 26032, rev C199, serial# 8328268 Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: audio processor is CX25841 (idx 35) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: decoder processor is CX25841 (idx 2Cool Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: has no radio, has IR remote Jun 6 10:00:25 mythtv kernel: ivtv0: Corrected autodetection from WinTV PVR 250 to WinTV PVR 150 Jun 6 10:00:25 mythtv kernel: eth0: no IPv6 routers present Jun 6 10:00:25 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) Jun 6 10:00:26 mythtv kernel: ivtv0: Encoder revision: 0x02050032 Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: tuner 1-0061: type set to 50 (TCL 2002N) Jun 6 10:00:26 mythtv kernel: ivtv0: Initialized WinTV PVR 150, card #0 Jun 6 10:00:26 mythtv kernel: ivtv: ==================== END INIT IVTV ==================== Jun 6 10:00:26 mythtv kernel: lirc_pvr150: ivtv i2c driver #0: no devices found Does this seem to be a IVTV problem or a LIRC problem? If someone has been able to get this to work could the let me kknow what version of the drivers they ended up using. I guess my next step would be to go to an older version if IVTV and/or LIRC but before I do that I would like to know if others have had any success. Any ideas appreciated. thanks Craig

Author:	SunTzuTech [ Wed Jun 07, 2006 11:34 am ]
Post subject:	Re: any luck getting pvr150 built in irblaster working?
iscraigh wrote: Reposting because I didn't want to hijack another persons post. The receiver and blaster on a pvr150 are not working for me. Irrecord spits out a message of "hardware not found". My /var/log/kern.log has the same message when lirc tries to load. Quote: Jun 6 10:00:21 mythtv kernel: lirc_dev: IR Remote Control driver registered, at major 61 Jun 6 10:00:21 mythtv kernel: ivtv: ==================== START INIT IVTV ==================== Jun 6 10:00:21 mythtv kernel: ivtv: version 0.4.4 (tagged release) loading Jun 6 10:00:21 mythtv kernel: ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3 Jun 6 10:00:21 mythtv kernel: ivtv: In case of problems please include the debug info between Jun 6 10:00:21 mythtv kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Jun 6 10:00:21 mythtv kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Jun 6 10:00:21 mythtv kernel: ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) Jun 6 10:00:21 mythtv kernel: ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 19 Jun 6 10:00:21 mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32) Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] Jun 6 10:00:21 mythtv kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Jun 6 10:00:21 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] Jun 6 10:00:21 mythtv kernel: cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) Jun 6 10:00:24 mythtv kernel: cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes) Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] Jun 6 10:00:24 mythtv kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) Jun 6 10:00:24 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: Hauppauge model 26032, rev C199, serial# 8328268 Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: audio processor is CX25841 (idx 35) Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: decoder processor is CX25841 (idx 2Cool Jun 6 10:00:25 mythtv kernel: tveeprom 1-0050: has no radio, has IR remote Jun 6 10:00:25 mythtv kernel: ivtv0: Corrected autodetection from WinTV PVR 250 to WinTV PVR 150 Jun 6 10:00:25 mythtv kernel: eth0: no IPv6 routers present Jun 6 10:00:25 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) Jun 6 10:00:26 mythtv kernel: ivtv0: Encoder revision: 0x02050032 Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) Jun 6 10:00:26 mythtv kernel: tuner 1-0061: type set to 50 (TCL 2002N) Jun 6 10:00:26 mythtv kernel: ivtv0: Initialized WinTV PVR 150, card #0 Jun 6 10:00:26 mythtv kernel: ivtv: ==================== END INIT IVTV ==================== Jun 6 10:00:26 mythtv kernel: lirc_pvr150: ivtv i2c driver #0: no devices found Does this seem to be a IVTV problem or a LIRC problem? If someone has been able to get this to work could the let me kknow what version of the drivers they ended up using. I guess my next step would be to go to an older version if IVTV and/or LIRC but before I do that I would like to know if others have had any success. Craig I upgraded the ivtv software to 0.4.5 and my remote and sound are working, but I get nothing but static on the screen, despite a dozen or so changes to the /etc/mythtv/modules/ivtv last night (and associated reboots). My PVR-150 is the model 1045 (with the dogbone remote and IRblaster on the same cable) HTH

Author:	tjc [ Wed Jun 07, 2006 5:55 pm ]
Post subject:
The 0.4.5 ivtv driver has issues. Mostly with locking up when you try to change the channel. I don't recommend using it. Installing 0.4.4 over the top of it should get you back to a working state.

Author:	cabl3guy [ Wed Jun 21, 2006 8:16 pm ]
Post subject:
I've almost given up on the PVR250 with a serial IR Blaster. I'm wanting to go buy the PVR150 ( 1045 ) and use the built in IR Blaster. Like Craig mentioned, is there a walk through for getting the built-in IR working for the PVR150 with R5C7? I found this one but I'm not sure if it's for the built-in IR or the serial. http://mysettopbox.tv/phpBB2/viewtopic.php?t=6206 I'll call you tonight Scott and ask you!

Author:	iscraigh [ Wed Jun 21, 2006 8:44 pm ]
Post subject:
Serial blaster should be easy to get working now. I did get the 150 blaster working can't remember what I finally did but just remember when you make a change do a full shutdown and leave the pc off for a minute to clear the ivtv registers. You can contact me if you want help with the serial one. Craig

LinHES Forums http://forum.linhes.org/

any luck getting pvr150 built in irblaster working? http://forum.linhes.org/viewtopic.php?f=2&t=10383	Page 1 of 1

Author:	rando [ Thu Jun 22, 2006 7:17 am ]
Post subject:
Here's what appears to be pretty complete directions in getting the 150 IR Blaster working. http://www.blushingpenguin.com/mark/blog/?p=24 I ran into issues when following these steps, but it seems others have followed this through and ended up with functioning systems. My troubles are detailed at the bottom of the page in the user comments section.

Page 1 of 1	All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/