| LinHES Forums http://forum.linhes.org/ |
|
| PCI cards not detected http://forum.linhes.org/viewtopic.php?f=2&t=12590 |
Page 1 of 1 |
| Author: | hfsoares [ Wed Nov 15, 2006 10:18 am ] |
| Post subject: | PCI cards not detected |
Hi people, I`m trying to install R5D1 but I cant detect my pci tv cards. These are the specs: CPU : Athlon 3800+ Board : Asus A8V-X Video : FX5200 Audio : On Board PCI : PVR-150 and a PixelView Prolink mpeg2 The main problem is that the PCI cards are not detected by the system. I`ve tryied also Suse and Ubuntu and both couldn`t detect the cards. I`ve installed Windows and they are good to go, so I`m confident that is a hardware compatibility issue. This is my lspci and dmesg results: lspci: 0000:00:00.0 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:00.1 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:00.2 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:00.3 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:00.4 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:00.7 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] 0000:00:0f.0 IDE interface: VIA Technologies, Inc. VT8251 AHCI/SATA 4-Port Controller 0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 07) 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90) 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90) 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90) 0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90) 0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 90) 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8251 PCI to ISA Bridge 0000:00:11.7 Host bridge: VIA Technologies, Inc. VT8251 Ultra VLINK Controller 0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 0000:00:13.0 PCI bridge: VIA Technologies, Inc. VT8251 Host Bridge 0000:00:13.1 PCI bridge: VIA Technologies, Inc. VT8251 PCI to PCI Bridge 0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) 0000:02:00.0 PCI bridge: VIA Technologies, Inc. VT8251 PCIE Root Port 0000:02:00.1 PCI bridge: VIA Technologies, Inc. VT8251 PCIE Root Port 0000:02:01.0 Audio device: VIA Technologies, Inc. VIA High Definition Audio Controller dmesg: Linux version 2.6.17-chw-8 (root@mythtv) (gcc version 3.4.4 20050314 (prerelease) (Debian 3.4.3-13)) #1 SMP PREEMPT Sun Jul 30 12:38:47 PDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable) BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data) BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000ff780 On node 0 totalpages: 262096 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32720 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP (v000 ACPIAM ) @ 0x000fa970 ACPI: RSDT (v001 A M I OEMRSDT 0x06000620 MSFT 0x00000097) @ 0x3ffd0000 ACPI: FADT (v002 A M I OEMFACP 0x06000620 MSFT 0x00000097) @ 0x3ffd0200 ACPI: MADT (v001 A M I OEMAPIC 0x06000620 MSFT 0x00000097) @ 0x3ffd0390 ACPI: MCFG (v001 A M I OEMMCFG 0x06000620 MSFT 0x00000097) @ 0x3ffd03f0 ACPI: OEMB (v001 A M I AMI_OEM 0x06000620 MSFT 0x00000097) @ 0x3ffde040 ACPI: DSDT (v001 A0304 A0304001 0x00000001 INTL 0x02002026) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=301 splash=silent apm=power-off nomce bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2400.122 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1032252k/1048384k available (4215k kernel code, 15548k reserved, 1593k data, 252k init, 130880k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4802.33 BogoMIPS (lpj=2401165) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 24k freed CPU0: AMD Athlon(tm) 64 Processor 3800+ stepping 02 Total of 1 processors activated (4802.33 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 Brought up 1 CPUs migration_cost=0 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 56k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on 0:0 PCI: No mmconfig possible on 0:1 PCI: No mmconfig possible on 0:f PCI: No mmconfig possible on 0:10 PCI: No mmconfig possible on 0:11 PCI: No mmconfig possible on 0:12 PCI: No mmconfig possible on 0:13 PCI: No mmconfig possible on 0:18 PCI: No mmconfig possible on 1:0 PCI: No mmconfig possible on 5:b PCI: No mmconfig possible on 5:d Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:13.1 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P9._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:07: ioport range 0xc00-0xc0f has been reserved pnp: 00:07: ioport range 0xd00-0xd0f has been reserved pnp: 00:07: ioport range 0xa20-0xa2f has been reserved pnp: 00:07: ioport range 0xa30-0xa3f has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: fc900000-fe9fffff PREFETCH window: afe00000-cfdfffff PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:02:00.1 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:13.0 IO window: disabled. MEM window: fea00000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:13.1 IO window: disabled. MEM window: disabled. PREFETCH window: cfe00000-d7efffff PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Setting latency timer of device 0000:00:13.0 to 64 PCI: Setting latency timer of device 0000:02:00.0 to 64 PCI: Setting latency timer of device 0000:02:00.1 to 64 PCI: Setting latency timer of device 0000:00:13.1 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFS: nTxBlock = 8066, nTxLock = 64533 SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: Setting latency timer of device 0000:02:00.0 to 64 pcie_portdrv_probe->Dev[287c:1106] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:00.0:pcie00] Allocate Port Service[0000:02:00.0:pcie01] Allocate Port Service[0000:02:00.0:pcie03] PCI: Setting latency timer of device 0000:02:00.1 to 64 pcie_portdrv_probe->Dev[287d:1106] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:00.1:pcie00] Allocate Port Service[0000:02:00.1:pcie01] Allocate Port Service[0000:02:00.1:pcie03] isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 7.0.33-k2 Copyright (c) 1999-2005 Intel Corporation. pcnet32.c:v1.32 18.Mar.2006 tsbogend@alpha.franken.de e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation ns83820.c: National Semiconductor DP83820 10/100/1000 driver. via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 16 eth0: VIA Rhine II at 0xfebff400, 00:17:31:b7:a6:e1, IRQ 16. eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1. forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54. dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker <becker@scyld.com> http://www.scyld.com/network/drivers.html uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 0 VP_IDE: chipset revision 7 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8251 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: ST3320620A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-ST RW/DVD GCC-4520B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 625142448 sectors (320072 MB) w/16384KiB Cache, CHS=38913/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 7144.000 MB/sec raid5: using function: pIII_sse (7144.000 MB/sec) raid6: int32x1 769 MB/s raid6: int32x2 1089 MB/s raid6: int32x4 714 MB/s raid6: int32x8 710 MB/s raid6: mmxx1 1511 MB/s input: AT Translated Set 2 keyboard as /class/input/input0 raid6: mmxx2 3003 MB/s raid6: sse1x1 914 MB/s raid6: sse1x2 1781 MB/s raid6: sse2x1 1777 MB/s raid6: sse2x2 2660 MB/s raid6: using algorithm sse2x2 (2660 MB/s) md: raid6 personality registered for level 6 md: multipath personality registered for level -4 md: faulty personality registered for level -5 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 15 Using IPI No-Shortcut mode Suspend2 Core. Suspend2 Compression Driver loading. Suspend2 Encryption Driver loading. Suspend2 Swap Writer loading. Suspend2 FileWriter loading. ACPI wakeup devices: PCI0 PS2K PS2M UAR1 USB1 USB2 USB3 USB4 EHCI P7P8 P7P9 PCI1 PCI2 PCI3 ILAN SLPB PWRB ACPI: (supports S0 S1 S3 S4 S5) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Suspend2 2.2.7.3: You need to use a resume2= command line parameter to tell Suspend2 where to look for an image. Suspend2 2.2.7.3: Resume2 parameter is empty. Suspending will be disabled. Suspend2 2.2.7.3: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending. (fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recovered transactions 41 to 134 (fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 3450 and revoked 3/3 blocks input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 252k freed Adding 1959920k swap on /dev/hda2. Priority:-1 extents:1 across:1959920k EXT3 FS on hda1, internal journal megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006 3ware Storage Controller device driver for Linux v1.26.02.001. 3ware 9000 Storage Controller device driver for Linux v2.26.02.007. Adaptec aacraid driver (1.1-5[2409]-mh1) usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 17 PCI: VIA IRQ fixup for 0000:00:10.0, from 10 to 1 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:10.0: irq 17, io base 0x0000e080 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 18 PCI: VIA IRQ fixup for 0000:00:10.1, from 5 to 2 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.1: irq 18, io base 0x0000e000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19 PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 3 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 19, io base 0x0000dc00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 16 PCI: VIA IRQ fixup for 0000:00:10.3, from 3 to 0 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 16, io base 0x0000d880 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 18 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: debug port 1 ehci_hcd 0000:00:10.4: irq 18, io mem 0xfebff800 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ieee1394: Initialized config rom entry `ip1394' Generic RTC Driver v1.07 ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU1] (supports 16 throttling states) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:02:01.0 to 64 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 128M @ 0xd8000000 NET: Registered protocol family 17 Linux video capture interface: v1.00 bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bt878: AUDIO driver version 0.0.0 loaded saa7146: register extension 'dvb'. saa7146: register extension 'budget dvb'. saa7146: register extension 'budget_ci dvb'. saa7146: register extension 'budget_av'. usbcore: registered new driver ttusb usbcore: registered new driver ttusb-dec usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ttyS1: LSR safety check engaged! ttyS1: LSR safety check engaged! kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! ts: Compaq touchscreen protocol output 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21 NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21 NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.7.0 (tagged release) loading ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv: ==================== END INIT IVTV ==================== eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: no IPv6 routers present Thx for any help |
|
| Author: | hfsoares [ Wed Nov 15, 2006 11:02 am ] |
| Post subject: | |
i`v seen a post (http://forums.viaarena.com/messageview. ... erthread=y) with the same problem that I have, but with ubuntu. The solution was? You can try the "pci=conf1" option in GRUB memu to boot the OS. The VT8251 Audio Controller should work with this option. But I don`t have a clue to how do this on knopmyth. Any help? []s Humberto |
|
| Author: | hfsoares [ Wed Nov 15, 2006 12:10 pm ] |
| Post subject: | |
A little more info: I've installed ubuntu and had the same problem. Gone to boot/grub/menu.lst and add the pci=conf1 and the cards were detected. So I'm confident that if I can do the same procedure on knoppmyh I will be able to install my machine. Any tips? []s Humberto |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|