| LinHES Forums http://forum.linhes.org/ |
|
| PVR-150 Won't Change Channels w/o modprobing http://forum.linhes.org/viewtopic.php?f=2&t=13488 |
Page 1 of 1 |
| Author: | Kadin2048 [ Sat Jan 13, 2007 3:33 pm ] |
| Post subject: | PVR-150 Won't Change Channels w/o modprobing |
So I have my MythTV system basically up and working, except for two things. The biggest problem I'm dealing with now, is that MythTV won't change the tuner's channels correctly after boot. In order to get it to work, I've had to log into a root console and type: rmmod ivtv modprobe ivtv tuner=50 After that, everything works fine. But this is a problem, because it means if the power goes off and comes back on, the system basically won't function until I can fix it. Does anyone know what might be causing this problem, and how to fix it? For reference, I'm using a PVR-150 with Knoppmyth R5D4. Below is the boot-time output of IVTV, obtained using "dmesg | grep ivtv". The output when I rmmmod/modprobe looks exactly the same. The only difference I can see is that when I rmmod/modprobe, I'm giving it the 'tuner=50' parameter explicitly. Is there any place where I can set that in the bootup scripts? I'd just like to avoid having to modprobe every time. Anyway, hope this questions hasn't been asked before; I did some searching and haven't found a solution. Bootup output: Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (tagged release) loading ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== |
|
| Author: | tjc [ Sat Jan 13, 2007 4:08 pm ] |
| Post subject: | |
See the second heading on this page. http://www.knoppmythwiki.org/index.php?page=TVCaptureCards |
|
| Author: | Kadin2048 [ Sat Jan 13, 2007 6:25 pm ] |
| Post subject: | |
That seemed to do it; thanks! (I just added an options line to my modprobe.conf and rebooted.) |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|