| LinHES Forums http://forum.linhes.org/ |
|
| Static with R5F1 and PVR-150 w/ ivtv-0.10.3 + firmware http://forum.linhes.org/viewtopic.php?f=2&t=15851 |
Page 1 of 1 |
| Author: | SunTzuTech [ Thu Jul 12, 2007 6:29 am ] |
| Post subject: | Static with R5F1 and PVR-150 w/ ivtv-0.10.3 + firmware |
Updated my old mythtv box, with a fresh install. The last time, I was required to install ivtv-0.4.5 to get my PVR-150 working. Now, both the version in R5F1 and the updated version in ivtv-0.10.3 plus the firmware are getting me static screens with some garbled audio. Ideas? HW: Aopen DX34Plus MB, 1.0Ghz PIII, 1.5GB Ram, PVR-150, SB Live 5.1, DLink 520 (Atheros wifi), Intel Pro/100 ethernet, Combo USB2.0/1394 card, 250G IDE disk. Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.3 (tagged release) loading ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 18 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090e6390000000d] eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) ivtv0: Encoder revision: 0x02060039 tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Linux agpgart interface v0.101 (c) Dave Jones tveeprom 1-0050: Hauppauge model 26132, rev G1B2, serial# 9519520 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR receiver, has IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-150 ivtv0: reopen i2c bus for IR-blaster support tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) wlan: 0.8.4.2 (0.9.3) ath_pci: 0.9.4.5 (0.9.3) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) tuner 1-0061: type set to 50 (TCL 2002N) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== |
|
| Author: | novellahub [ Thu Jul 12, 2007 11:44 am ] |
| Post subject: | |
What size are you capturing video? 720X480 should be set for the PVR-150 or PVR-500 cards. Otherwise the picture quality is degrated in both models. |
|
| Author: | tjc [ Thu Jul 12, 2007 6:12 pm ] |
| Post subject: | |
Didn't I reply to this already? You didn't post the orginal under installation did you? In any case, most likely configuration. Look at the frequency sets as described on the BlackScreenWatchingTV troubleshooting page on the wiki. Links below. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|