LinHES Forums
http://forum.linhes.org/

PVR250 - 4001
http://forum.linhes.org/viewtopic.php?f=2&t=2683		 Page 1 of 1
Author:  Paul Weaver [ Thu Oct 14, 2004 11:56 am ]
Post subject:  PVR250 - 4001
I'm trying to set my PVR250 up (it doesnt work straight off), however most of the docs I've found mention device 4009. I've got device 4001. Does anyone else have this? I'm assuming I'll have to recompile ivtv as it's not working at the moment. To start with, the ivtv module isn't loaded, after modprobe ivtv, test_ioctl -a gives lots of sparkly data, but test_ioctl -u=0x000000FF (change to PAL) fails.
ioctl: VIDIOC_S_STD
ioctl: VIDIOC_S_STD failed

Heres lspci -vv -s 00:09

00:09.0 Multimedia video controller: Internext Compression Inc iTVC15 MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 4001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

lsmod:
ivtv 85572 0
i2c-algo-bit 7048 1 [ivtv]
i2c-core 12452 0 [ivtv i2c-algo-bit]
videodev 6016 3 [ivtv]
tdfx 31800 2
soundcore 3524 0 (autoclean)
autofs4 9332 0 (unused)
af_packet 14632 0 (unused)
nls_iso8859-1 2812 0 (unused)
nls_cp437 4316 0 (unused)
agpgart 42852 0 (unused)
8139too 14664 1
mii 2176 0 [8139too]
crc32 2848 0 [8139too]
serial 44708 1
usb-uhci 22960 0 (unused)
usbcore 59980 0 [usb-uhci]
rtc 7432 0
ext3 65604 2
jbd 47952 2 [ext3]

and test_ioctl -a
ioctl: IVTV_IOC_G_CODEC
Codec parameters
aspect : 2
audio : 0x00e9
bframes : 3
bitrate_mode: 0
bitrate : 8000000
bitrate_peak: 16000000
dnr_mode : 0
dnr_spatial : 0
dnr_temporal: 0
dnr_type : 0
framerate : 0
framespergop: 15
gop_closure : 0
pulldown : 0
stream_type : 0
ioctl: VIDIOC_G_FMT
Type : Video Capture
Width : 720
Height : 480
ioctl: VIDIOC_QUERYCAP
Driver name : ivtv
Card type : Vanilla iTVC15 card
Bus info : 0
Driver version: 265
Capabilities : 0x01030001
ioctl: VIDIOC_ENUMINPUT
Name : Composite 0
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : Composite 1
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : Composite 2
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : Composite 3
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : Tuner 0
Type : 0x00000001
Audioset: 0x00000000
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : Composite 4
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : S-Video 0
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : S-Video 1
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : S-Video 2
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
Name : S-Video 3
Type : 0x00000002
Audioset: 0x00000001
Tuner : 0x00000000
Standard: 0x 3000 ( NTSC )
Status : 0
ioctl: VIDIOC_G_INPUT
Input = 4
ioctl: VIDIOC_G_FREQUENCY
Frequency = 0
ioctl: VIDIOC_ENUMSTD
ID : 0x 3000
Name : NTSC
Frame period: 1001/30000
Frame lines : 525
ID : 0x FF
Name : PAL
Frame period: 1/25
Frame lines : 625
ID : 0x 7F0000
Name : SECAM
Frame period: 1/25
Frame lines : 625
ioctl: VIDIOC_G_STD
Standard = 0x00003000
ioctl: VIDIOC_QUERYCTRL
Brightness = 514
Contrast = -984778240
Saturation = -1054878112
Hue = 0
Volume = 0
Mute = 0
Author:  RacerX [ Thu Oct 14, 2004 12:14 pm ]
Post subject:  PVR-250 MCE
Hello

The problem that your speaking of lies in the hardware. The Pvr-250 (401) is called a PVR-250 MCE. It is a newer model of the card and many people are using it. It you do a search on MCE there is quite a lot of info on this card. Basically you need to recompile to a newer version of the IVTV driver in order to get it to work correctly.

Good Luck
Author:  Paul Weaver [ Fri Oct 15, 2004 6:14 am ]
Post subject: 
I've had a search arround, but the MCE version apparently doesn't come with a remote control (mine does).

Unfortunatly I just managed to get a kernel panic on my box, and I'm 30 miles away for the rest of the day. Very annoying
Author:  RacerX [ Fri Oct 15, 2004 11:55 am ]
Post subject: 
I see it might help to try and ID the card by the Conexant Chip CX... model number

Here is good link with pictures of PVR-250. There are quite a few different flavors....

http://www.shspvr.com/pvr_model.html

I still recommend recompiling IVTV and see if that helps you out.

Good Luck
Author:  Paul Weaver [ Sat Oct 16, 2004 6:20 am ]
Post subject: 
I compiled 0.2.0-rc1a, and it seems to recognise everything. Remote works fine, loads automatically on boot, but cat /dev/video doesnt return anything.

I've also tried 0.1.10pre2-ck115i, same result.

tveeprom output:
Oct 14 22:26:52 leela kernel: tveeprom: Hauppauge: model = 48015, rev = G535, serial# = 2680088
Oct 14 22:26:52 leela kernel: tveeprom: tuner = Temic 4066FY5 (idx = 35, type = 18)
Oct 14 22:26:52 leela kernel: tveeprom: tuner fmt = PAL(I) (eeprom = 0x10, v4l2 = 0x00000010)
Oct 14 22:26:52 leela kernel: tveeprom: audio_processor = MSP3415 (type = 6)

Any ideas? What are the latest drivers, there seem to be 3 branches (0.1, 0.2 and 0.3).

Couldn't spot my card on that page.

Should "tuner" be bound to ivtv when I lsmod?

tuner 12712 1 (autoclean)
i2c-core 12452 0 (autoclean) [lirc_i2c tveeprom msp3400 saa7115 tuner i2c-algo-bit]
ivtv 790912 4 (autoclean)
i2c-algo-bit 7048 1 (autoclean) [ivtv]
videodev 6016 5 (autoclean) [ivtv]
lirc_i2c 4448 1 (autoclean)
lirc_dev 8592 1 (autoclean) [lirc_i2c]
Author:  tjc [ Sat Oct 16, 2004 12:31 pm ]
Post subject: 
Have you been able to identify the exact model of card yet?
Author:  Paul Weaver [ Sat Oct 16, 2004 5:57 pm ]
Post subject: 
I'm pretty certain it's a "Retail Boxed Hauppuage WinTV-PVR 250 revision 1 Conexant CX23415 chip with heatsinker.
(Notice the older design with the missing white feature connector)"

(Hauppauge PVR250, Rev1: Models 48xxx, S-Video connector only, comes with composite adapter, http://ivtv.writeme.ch/tiki-index.php?p ... edHardware states it's supported )

Model 48015 REV G535 PAL-I Tuner. Chip hidden under headsink. 480000-05A (C) 2002 in the top right corner.

Hope that's enough to ID it, I dont really want to take the heatsink off or start unsoldering things.

On the back there's a label with "41 02 2680088" on it.
Author:  tjc [ Sat Oct 16, 2004 6:20 pm ]
Post subject: 
Have you double checked that the right frequency set is selected in setup and that you've got it tuned to a real channel? Have you tried taking a signal from one of the other inputs like svideo?
Author:  RacerX [ Sat Oct 16, 2004 7:07 pm ]
Post subject: 
Interesting so your card is an original PVR-250 and not MCE. I would think that IVTV should work straight out of the box and you would just have to config it for PAL.

You might want to look over to knoppmythwiki and see if that provides you a bit more insight into PAL specific changes.

http://knoppmythwiki.homelinux.org/inde ... e=PalHowTo

Hope this helps
Author:  Paul Weaver [ Tue Oct 19, 2004 7:00 am ]
Post subject: 
I reinstalled from scratch last night, blew away the partitions and everything. Booted up, installed the latest xmltv, configed it for pal followign those instructions

I now get cat: /dev/video: Input/output error after ~ 3.3 seconds. I'm guessing the SAA regs might be a problem (whatever they are)


Code:
ioctl: Input detect failed (cannot read SAA regs)
ioctl: Input detect failed (cannot read SAA regs)
ioctl: VIDEO_STATUS = Bad

SAA7115 reg[STATUS#1 - 0x1E] = 00
 Color Standard (D0-D1): BW/No color
 White peak loop (D2): Not activated
 Gain value for act.lum. (min) (D3): Not limited
 Gain value for act.lum. (max) (D4): Not limited
 WIPA-mode slow-time constant (D5): Not activated
 Horizontal frequency (D6): Locked
 Field length (D7): Non-standard

SAA7115 reg[STATUS#2 - 0x1F] = 00
 Ready for capture (D0): No
 Macrovision 7.01 (D1): No
 MV Colorstripe burst (D2): No
 MV Colorstripe burst type 3 (D3): No
 Input signal timebase (D4): Non-stable (VCR)
 Field frequency (D5): 50Hz
 H & V loops (D6): Locked
 Interlace (D7): Not detected



edit:
I assume Saa7115 is the decoder ship, and the "regs" are registers on the chip.
Author:  RacerX [ Tue Oct 19, 2004 4:06 pm ]
Post subject: 
To start

Can you please post the output of

lspci -v

and

/var/log/messages

That will give us a better understanding of your hardware to try and isolate the root cause of the problem. Clearly it doesn't work straight out of the box with the directions. The question now is the problem a hardware conflict...something with the computer ...or the card chipset wth the IVTV driver.

thanks
Author:  Paul Weaver [ Wed Oct 20, 2004 5:50 am ]
Post subject: 
lspci -v
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Flags: bus master, medium devsel, latency 32
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0

00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d4000000-d7ffffff
Prefetchable memory behind bridge: dc000000-ddffffff

00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Flags: bus master, medium devsel, latency 0

00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 32
I/O ports at f000 [size=16]

00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d000 [size=32]

00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Flags: medium devsel, IRQ 9

00:09.0 Multimedia video controller: Internext Compression Inc iTVC15 MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 4001
Flags: bus master, medium devsel, latency 64, IRQ 14
Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Allied Telesyn International AT-2500TX/ACPI
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d400 [size=256]
Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 1

00:13.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 11
I/O ports at d800 [size=8]
I/O ports at dc00 [size=4]
I/O ports at e000 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]

00:13.1 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 11
I/O ports at e400 [size=8]
I/O ports at e800 [size=4]
I/O ports at ec00 [size=256]

01:00.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3 AGP
Flags: 66Mhz, fast devsel, IRQ 12
Memory at d4000000 (32-bit, non-prefetchable) [size=32M]
Memory at dc000000 (32-bit, prefetchable) [size=32M]
I/O ports at c000 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [54] AGP version 1.0
Capabilities: [60] Power Management version 1

Oct 18 22:06:14 leela syslogd 1.4.1#10: restart.
Oct 18 22:06:14 leela kernel: klogd 1.4.1#10, log source = /proc/kmsg started.
Oct 18 22:06:14 leela kernel: Inspecting /boot/System.map-2.4.25-chw
Oct 18 22:06:15 leela kernel: Loaded 18648 symbols from /boot/System.map-2.4.25-chw.
Oct 18 22:06:15 leela kernel: Symbols match kernel version 2.4.25.
Oct 18 22:06:15 leela kernel: Loaded 1181 symbols from 20 modules.
Oct 18 22:06:15 leela kernel: Linux version 2.4.25-chw (root@km_dev.mysettopbox.tv) (gcc version 3.3.2 20030812 (Debian prerelease)) #1 Sat Apr 10 15:46:31 PDT 2004
Oct 18 22:06:15 leela kernel: BIOS-provided physical RAM map:
Oct 18 22:06:15 leela kernel: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Oct 18 22:06:15 leela kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Oct 18 22:06:15 leela kernel: BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
Oct 18 22:06:15 leela kernel: BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
Oct 18 22:06:15 leela kernel: BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
Oct 18 22:06:15 leela kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Oct 18 22:06:15 leela kernel: 0MB HIGHMEM available.
Oct 18 22:06:15 leela kernel: 127MB LOWMEM available.
Oct 18 22:06:15 leela kernel: On node 0 totalpages: 32752
Oct 18 22:06:15 leela kernel: zone(0): 4096 pages.
Oct 18 22:06:15 leela kernel: zone(1): 28656 pages.
Oct 18 22:06:15 leela kernel: zone(2): 0 pages.
Oct 18 22:06:15 leela kernel: Kernel command line: auto BOOT_IMAGE=knoppix ro root=301 hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
Oct 18 22:06:15 leela kernel: ide_setup: hda=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdb=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdc=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdd=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hde=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdf=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdg=scsi
Oct 18 22:06:15 leela kernel: ide_setup: hdh=scsi
Oct 18 22:06:15 leela kernel: Initializing CPU#0
Oct 18 22:06:15 leela kernel: Detected 601.370 MHz processor.
Oct 18 22:06:15 leela kernel: Console: colour dummy device 80x25
Oct 18 22:06:15 leela kernel: Calibrating delay loop... 1199.30 BogoMIPS
Oct 18 22:06:15 leela kernel: Memory: 126676k/131008k available (1363k kernel code, 3948k reserved, 490k data, 116k init, 0k highmem)
Oct 18 22:06:15 leela kernel: Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Oct 18 22:06:15 leela kernel: Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Oct 18 22:06:15 leela kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Oct 18 22:06:15 leela kernel: Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Oct 18 22:06:15 leela kernel: Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 18 22:06:15 leela kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Oct 18 22:06:15 leela kernel: CPU: L2 cache: 256K
Oct 18 22:06:15 leela kernel: CPU serial number disabled.
Oct 18 22:06:15 leela kernel: CPU: Intel Pentium III (Coppermine) stepping 01
Oct 18 22:06:15 leela kernel: Enabling fast FPU save and restore... done.
Oct 18 22:06:15 leela kernel: Enabling unmasked SIMD FPU exception support... done.
Oct 18 22:06:15 leela kernel: Checking 'hlt' instruction... OK.
Oct 18 22:06:15 leela kernel: POSIX conformance testing by UNIFIX
Oct 18 22:06:15 leela kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
Oct 18 22:06:15 leela kernel: mtrr: detected mtrr type: Intel
Oct 18 22:06:15 leela kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb520, last bus=1
Oct 18 22:06:15 leela kernel: PCI: Using configuration type 1
Oct 18 22:06:15 leela kernel: PCI: Probing PCI hardware
Oct 18 22:06:15 leela kernel: PCI: Probing PCI hardware (bus 00)
Oct 18 22:06:15 leela kernel: PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
Oct 18 22:06:15 leela kernel: Limiting direct PCI/PCI transfers.
Oct 18 22:06:15 leela kernel: isapnp: Scanning for PnP cards...
Oct 18 22:06:15 leela kernel: isapnp: SB audio device quirk - increasing port range
Oct 18 22:06:15 leela kernel: isapnp: Card 'Creative SB16 PnP'
Oct 18 22:06:15 leela kernel: isapnp: 1 Plug & Play card detected total
Oct 18 22:06:15 leela kernel: Linux NET4.0 for Linux 2.4
Oct 18 22:06:15 leela kernel: Based upon Swansea University Computer Society NET3.039
Oct 18 22:06:15 leela kernel: Initializing RT netlink socket
Oct 18 22:06:15 leela kernel: Starting kswapd
Oct 18 22:06:15 leela kernel: VFS: Disk quotas vdquot_6.5.1
Oct 18 22:06:15 leela kernel: vesafb: framebuffer at 0xdc000000, mapped to 0xc880d000, size 1875k
Oct 18 22:06:15 leela kernel: vesafb: mode is 800x600x16, linelength=1600, pages=16
Oct 18 22:06:15 leela kernel: vesafb: protected mode interface info at c000:7eef
Oct 18 22:06:15 leela kernel: vesafb: scrolling: redraw
Oct 18 22:06:15 leela kernel: vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Oct 18 22:06:15 leela kernel: Looking for splash picture... no good signature found.
Oct 18 22:06:15 leela kernel: Console: switching to colour frame buffer device 100x37
Oct 18 22:06:15 leela kernel: fb0: VESA VGA frame buffer device
Oct 18 22:06:15 leela kernel: Detected PS/2 Mouse Port.
Oct 18 22:06:15 leela kernel: pty: 256 Unix98 ptys configured
Oct 18 22:06:15 leela kernel: Floppy drive(s): fd0 is 1.44M
Oct 18 22:06:15 leela kernel: FDC 0 is a post-1991 82077
Oct 18 22:06:15 leela kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Oct 18 22:06:15 leela kernel: loop: loaded (max 8 devices)
Oct 18 22:06:15 leela kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Oct 18 22:06:15 leela kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Oct 18 22:06:15 leela kernel: PIIX4: IDE controller at PCI slot 00:07.1
Oct 18 22:06:15 leela kernel: PIIX4: chipset revision 1
Oct 18 22:06:15 leela kernel: PIIX4: not 100%% native mode: will probe irqs later
Oct 18 22:06:15 leela kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Oct 18 22:06:15 leela kernel: HPT366: onboard version of chipset, pin1=1 pin2=2
Oct 18 22:06:15 leela kernel: HPT366: IDE controller at PCI slot 00:13.0
Oct 18 22:06:15 leela kernel: PCI: Found IRQ 11 for device 00:13.0
Oct 18 22:06:15 leela kernel: PCI: Sharing IRQ 11 with 00:13.1
Oct 18 22:06:15 leela kernel: HPT366: chipset revision 1
Oct 18 22:06:15 leela kernel: HPT366: not 100%% native mode: will probe irqs later
Oct 18 22:06:15 leela kernel: ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
Oct 18 22:06:15 leela kernel: PCI: Found IRQ 11 for device 00:13.1
Oct 18 22:06:15 leela kernel: PCI: Sharing IRQ 11 with 00:13.0
Oct 18 22:06:15 leela kernel: ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:DMA, hdf:DMA
Oct 18 22:06:15 leela kernel: hda: HDS722512VLAT20, ATA DISK drive
Oct 18 22:06:15 leela kernel: hdb: HDS722512VLAT20, ATA DISK drive
Oct 18 22:06:15 leela kernel: hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Oct 18 22:06:15 leela kernel: hda: set_drive_speed_status: error=0x04 { DriveStatusError }
Oct 18 22:06:15 leela kernel: hdb: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Oct 18 22:06:15 leela kernel: hdb: set_drive_speed_status: error=0x04 { DriveStatusError }
Oct 18 22:06:15 leela kernel: hdc: R/RW 8x4x32, ATAPI CD/DVD-ROM drive
Oct 18 22:06:15 leela kernel: hde: WDC WD307AA-00BAA0, ATA DISK drive
Oct 18 22:06:15 leela kernel: hdf: QUANTUM FIREBALLlct15 30, ATA DISK drive
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: error=0x04 { DriveStatusError }
Oct 18 22:06:15 leela kernel: ide0 at 0xd800-0xd807,0xdc02 on irq 11
Oct 18 22:06:15 leela kernel: ide1 at 0x170-0x177,0x376 on irq 15
Oct 18 22:06:15 leela kernel: ide2 at 0xe400-0xe407,0xe802 on irq 11
Oct 18 22:06:15 leela kernel: hda: attached ide-disk driver.
Oct 18 22:06:15 leela kernel: hda: host protected area => 1
Oct 18 22:06:15 leela kernel: hda: 241254720 sectors (123522 MB) w/1794KiB Cache, CHS=15017/255/63
Oct 18 22:06:15 leela kernel: hdb: attached ide-disk driver.
Oct 18 22:06:15 leela kernel: hdb: host protected area => 1
Oct 18 22:06:15 leela kernel: hdb: 241254720 sectors (123522 MB) w/1794KiB Cache, CHS=15017/255/63
Oct 18 22:06:15 leela kernel: hde: attached ide-disk driver.
Oct 18 22:06:15 leela kernel: hde: host protected area => 1
Oct 18 22:06:15 leela kernel: hde: 60074784 sectors (30758 MB) w/2048KiB Cache, CHS=59598/16/63
Oct 18 22:06:15 leela kernel: hdf: attached ide-disk driver.
Oct 18 22:06:15 leela kernel: hdf: host protected area => 1
Oct 18 22:06:15 leela kernel: hdf: 58633344 sectors (30020 MB) w/418KiB Cache, CHS=58168/16/63
Oct 18 22:06:15 leela kernel: ide-cd: passing drive hdc to ide-scsi emulation.
Oct 18 22:06:15 leela kernel: hdc: attached ide-scsi driver.
Oct 18 22:06:15 leela kernel: Partition check:
Oct 18 22:06:15 leela kernel: hda: hda1 hda2 hda3 hda4
Oct 18 22:06:15 leela kernel: hdb:
Oct 18 22:06:15 leela kernel: hde: hde1 hde2 hde3
Oct 18 22:06:15 leela kernel: hdf: [PTBL] [3649/255/63] hdf1
Oct 18 22:06:15 leela kernel: Highpoint HPT370 Softwareraid driver for linux version 0.02
Oct 18 22:06:15 leela kernel: Guestimating sector 241231784 for superblock
Oct 18 22:06:15 leela kernel: Guestimating sector 241231784 for superblock
Oct 18 22:06:15 leela kernel: Guestimating sector 60074719 for superblock
Oct 18 22:06:15 leela kernel: Guestimating sector 58633279 for superblock
Oct 18 22:06:15 leela kernel: SCSI subsystem driver Revision: 1.00
Oct 18 22:06:15 leela kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Oct 18 22:06:15 leela kernel: Vendor: IDE-CD Model: R/RW 8x4x32 Rev: 1.5
Oct 18 22:06:15 leela kernel: Type: CD-ROM ANSI SCSI revision: 02
Oct 18 22:06:15 leela kernel: Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Oct 18 22:06:15 leela kernel: sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Oct 18 22:06:15 leela kernel: Uniform CD-ROM driver Revision: 3.12
Oct 18 22:06:15 leela kernel: Initializing Cryptographic API
Oct 18 22:06:15 leela kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Oct 18 22:06:15 leela kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Oct 18 22:06:15 leela kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
Oct 18 22:06:15 leela kernel: TCP: Hash tables configured (established 8192 bind 16384)
Oct 18 22:06:15 leela kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Oct 18 22:06:15 leela kernel: RAMDISK: Compressed image found at block 0
Oct 18 22:06:15 leela kernel: Freeing initrd memory: 150k freed
Oct 18 22:06:15 leela kernel: VFS: Mounted root (ext2 filesystem).
Oct 18 22:06:15 leela kernel: Journalled Block Device driver loaded
Oct 18 22:06:15 leela kernel: kjournald starting. Commit interval 5 seconds
Oct 18 22:06:15 leela kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Oct 18 22:06:15 leela kernel: EXT3-fs: mounted filesystem with ordered data mode.
Oct 18 22:06:15 leela kernel: Freeing unused kernel memory: 116k freed
Oct 18 22:06:15 leela kernel: Unable to find swap-space signature
Oct 18 22:06:15 leela kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Oct 18 22:06:15 leela kernel: Real Time Clock Driver v1.10f
Oct 18 22:06:15 leela kernel: usb.c: registered new driver usbdevfs
Oct 18 22:06:15 leela kernel: usb.c: registered new driver hub
Oct 18 22:06:15 leela kernel: usb-uhci.c: $Revision: 1.275 $ time 16:10:01 Apr 10 2004
Oct 18 22:06:15 leela kernel: usb-uhci.c: High bandwidth mode enabled
Oct 18 22:06:15 leela kernel: PCI: Found IRQ 10 for device 00:07.2
Oct 18 22:06:15 leela kernel: PCI: Sharing IRQ 10 with 00:0b.0
Oct 18 22:06:15 leela kernel: usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 10
Oct 18 22:06:15 leela kernel: usb-uhci.c: Detected 2 ports
Oct 18 22:06:15 leela kernel: usb.c: new USB bus registered, assigned bus number 1
Oct 18 22:06:15 leela kernel: hub.c: USB hub found
Oct 18 22:06:15 leela kernel: hub.c: 2 ports detected
Oct 18 22:06:15 leela kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Oct 18 22:06:15 leela kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
Oct 18 22:06:15 leela kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Oct 18 22:06:15 leela kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Oct 18 22:06:15 leela kernel: 8139too Fast Ethernet driver 0.9.26
Oct 18 22:06:15 leela kernel: PCI: Found IRQ 10 for device 00:0b.0
Oct 18 22:06:15 leela kernel: PCI: Sharing IRQ 10 with 00:07.2
Oct 18 22:06:15 leela kernel: eth0: RealTek RTL8139 at 0xc8a33000, 00:a0:d2:a5:c4:64, IRQ 10
Oct 18 22:06:15 leela kernel: Linux agpgart interface v0.99 (c) Jeff Hartmann
Oct 18 22:06:15 leela kernel: agpgart: Maximum main memory to use for agp memory: 94M
Oct 18 22:06:15 leela kernel: agpgart: Detected Intel 440BX chipset
Oct 18 22:06:15 leela kernel: agpgart: AGP aperture is 64M @ 0xd0000000
Oct 18 22:06:15 leela kernel: NTFS driver v1.1.22 [Flags: R/W MODULE]
Oct 18 22:06:15 leela kernel: SGI XFS with realtime, no debug enabled
Oct 18 22:06:15 leela kernel: SGI XFS Quota Management subsystem
Oct 18 22:06:15 leela kernel: kjournald starting. Commit interval 5 seconds
Oct 18 22:06:15 leela kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal
Oct 18 22:06:15 leela kernel: EXT3-fs: mounted filesystem with ordered data mode.
Oct 18 22:06:15 leela kernel: Unable to find swap-space signature
Oct 18 22:06:15 leela kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Oct 18 22:06:15 leela kernel: blk: queue c0316928, I/O limit 4095Mb (mask 0xffffffff)
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: error=0x04 { DriveStatusError }
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Oct 18 22:06:15 leela kernel: hdf: set_drive_speed_status: error=0x04 { DriveStatusError }
Oct 18 22:06:15 leela kernel: blk: queue c0316a64, I/O limit 4095Mb (mask 0xffffffff)
Oct 18 22:06:45 leela kernel: [drm] Initialized tdfx 1.0.0 20010216 on minor 0
Oct 18 22:07:52 leela kernel: Linux video capture interface: v1.00
Oct 18 22:07:52 leela kernel: i2c-core.o: i2c core module version 2.6.1 (20010830)
Oct 18 22:07:52 leela kernel: i2c-algo-bit.o: i2c bit algorithm module
Oct 18 22:07:52 leela kernel: ivtv: version 0.1.9 (release) loading
Oct 18 22:07:52 leela kernel: ivtv: SGarray_size = 340, DSGarray_size = 16
Oct 18 22:07:52 leela kernel: ivtv: Found an iTVC15 based chip
Oct 18 22:07:52 leela kernel: PCI: Found IRQ 14 for device 00:09.0
Oct 18 22:07:52 leela kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Oct 18 22:07:55 leela kernel: ivtv: Encoder revision: 0x02040011
Oct 18 22:07:55 leela kernel: ivtv: Decoder revision: 0x02020023
Oct 18 22:07:55 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:07:55 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:07:55 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:07:55 leela kernel: ivtv: Registered v4l2 device, minor 0
Oct 18 22:07:55 leela kernel: ivtv: Registered v4l2 device, minor 32
Oct 18 22:07:55 leela kernel: ivtv: Registered v4l2 device, minor 224
Oct 18 22:07:55 leela kernel: ivtv: loaded
Oct 18 22:08:04 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:08:04 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:08:04 leela kernel: spurious 8259A interrupt: IRQ7.
Oct 18 22:08:10 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x803c4030
Oct 18 22:08:10 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0485630
Oct 18 22:08:10 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x8004562e
Oct 18 22:08:10 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0345641
Oct 18 22:08:10 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80345621
Oct 18 22:08:10 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:08:10 leela last message repeated 3 times
Oct 18 22:08:10 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:08:10 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:08:13 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0345641
Oct 18 22:08:16 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:08:16 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:08:40 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x803c4030
Oct 18 22:08:40 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0485630
Oct 18 22:08:40 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x8004562e
Oct 18 22:08:40 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0345641
Oct 18 22:08:40 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80345621
Oct 18 22:08:40 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:08:40 leela last message repeated 3 times
Oct 18 22:08:40 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:08:40 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:08:51 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x803c4030
Oct 18 22:08:51 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0485630
Oct 18 22:08:51 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x8004562e
Oct 18 22:08:51 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc0345641
Oct 18 22:08:51 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80345621
Oct 18 22:08:51 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:08:51 leela last message repeated 3 times
Oct 18 22:08:51 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:08:51 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:09:39 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:09:39 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:09:39 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:10:51 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:10:54 leela last message repeated 2 times
Oct 18 22:11:05 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:11:05 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:13:29 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:29 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:32 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:13:32 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:32 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:32 leela kernel: ivtv: 100 ms time out waiting for firmware
Oct 18 22:13:32 leela kernel: ivtv: api call 0x00000081
Oct 18 22:13:32 leela kernel: ivtv: startcap error 1. Code -16
Oct 18 22:13:32 leela kernel: ivtv: 1000 ms time out waiting for firmware
Oct 18 22:13:32 leela kernel: ivtv: api call 0x00000082
Oct 18 22:13:32 leela kernel: ivtv: stopcap error 2. Code -16
Oct 18 22:13:36 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:36 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:13:39 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:14:16 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:14:19 leela last message repeated 3 times
Oct 18 22:15:02 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:15:02 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:15:02 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:15:06 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:15:22 leela last message repeated 5 times
Oct 18 22:15:26 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:15:26 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:15:29 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:15:41 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:15:41 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:15:44 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:16:13 leela kernel: tveeprom.c: starting probe for adapter ivtv i2c driver #0 (0x10005)
Oct 18 22:16:13 leela kernel: tveeprom.c: detecting tveeprom client on address 0xa0
Oct 18 22:16:13 leela kernel: 18 [00] 05 50 13 5f 10 23 23 8f bb d5 54 9d 00 00 00 00 04
Oct 18 22:16:13 leela kernel: 10 [01] 01 20 77 00 40 18 e5 28 00
Oct 18 22:16:13 leela kernel: 4 [02] 01 86 00
Oct 18 22:16:13 leela kernel: tvee: Hauppauge: model=48015, rev=G535, serial#=2680088
Oct 18 22:16:13 leela kernel: tvee: tuner=Temic 4066FY5 (idx=35, type=18)
Oct 18 22:16:13 leela kernel: tvee: tuner fmt=PAL(I) (eeprom=0x10, v4l2=0x00000010)
Oct 18 22:16:13 leela kernel: tvee: audio_processor=MSP3415 (type=6)
Oct 18 22:19:41 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:19:41 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:19:44 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:19:48 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:19:48 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:19:51 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:20:17 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:17 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:20 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:20:21 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:21 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:24 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:20:40 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:40 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:43 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:20:45 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:45 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:20:48 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:21:34 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80144027
Oct 18 22:21:42 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:21:42 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:21:42 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:21:44 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80144027
Oct 18 22:21:50 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:21:56 leela last message repeated 257 times
Oct 18 22:22:46 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:22:46 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:22:46 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:23:25 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:23:25 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:23:25 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:23:30 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:23:30 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:23:33 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:23:39 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:23:39 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0xc00240ce
Oct 18 22:23:49 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:23:49 leela kernel: ivtv: i2c client addr: 0x61 not found!
Oct 18 22:23:49 leela kernel: ivtv: i2c client addr: 0x40 not found!
Oct 18 22:23:52 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:23:52 leela kernel: ivtv: i2c client addr: 0x21 not found!
Oct 18 22:23:55 leela kernel: ivtv: Timeout waiting for data!
Oct 18 22:24:03 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x80044037
Oct 18 22:24:08 leela kernel: ivtv: ivtv-api.c: unknown ioctl 0x000040ca

(hdf's got a dodgy cable but it's not used at the moment)
Author:  RacerX [ Wed Oct 20, 2004 1:57 pm ]
Post subject: 
From the /var/log/messages you can very clearly see that IVTV is not loading correctly.

Here are the directions to recompile IVTV ....they work for me...

http://mysettopbox.tv/phpBB2/viewtopic.php?t=2295

You can use these directions to test the various versions of IVTV found at

http://67.18.1.101/~ckennedy/ivtv/

However, if that does not work for you I would recommend contacting the IVTV developers and tell them about your card. It is possible that they my have to update the IVTV driver to support your version of the card.

http://ivtv.sourceforge.net/FAQ.html

It would be great if you could solve this problem and post the solution

Good Luck
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/