dmesg output:
Code:
bttv: Bt8xx card found (1).
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
bttv1: Bt878 (rev 17) at 0000:00:0f.0, irq: 5, latency: 32, mmio: 0xeb002000
bttv1: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID is 1461:0771
bttv1: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected]
bttv1: gpio: en=00000000, out=00000000 in=00ffffdf [init]
bttv1: using tuner=4
bttv1: registered device video1
bttv1: registered device vbi1
bttv1: PLL: 28636363 => 35468950 .. ok
bttv1: add subdevice "remote1"
bttv1: add subdevice "dvb1"
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0b.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xd800. Vers LK1.1.19
eth0: Dropping NETIF_F_SG since no checksum feature.
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0509440(lo)
IPv6 over IPv4 tunneling driver
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:00:0d.1[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
bt878(0): Bt878 (rev 2) at 00:0d.1, irq: 5, latency: 32, memory: 0xeb001000
bt878: Bt878 AUDIO function found (1).
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
bt878(1): Bt878 (rev 17) at 00:0f.1, irq: 5, latency: 32, memory: 0xeb003000
DVB: registering new adapter (bttv1).
mt352_read_register: readreg error (reg=127, ret==-5)
dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem 1461/0771
I have enabled the right module.
Soetimes it will be detected but the most time not.
But when i open my Case and switch it to an other PCI-Slot it works, but after the next reboot not more
I did all what i found in google, disabled ACPI, disabled USB and other things in BIOS, flashed the newest BIOS, installed the newest Kernel 2.6.12.5....but nothing worked
this Card is great, when it works....
System:
Athlon 1,4Ghz
Abit KR7A-RAID
Ati 9200SE
Knoppmyth R5.16