#!/usr/bin/perl
# ORIGINALLY:
# dss_control: Remote control of a Sony DSS unit via the serial port
# By Josh Wilmes (http://www.hitchhiker.org/dss)
# Based on info from http://www.isd.net/mevenmo/audiovideo.html
#
# I take no responsibility for any damage this script might cause.
# Feel free to modify and redistribute this as you see fit, but please retain
# the comments above.
#
# BASED ON:
# sony.pl - Found at tarek.2y.net/myth/
#
# CURRENTLY:
# sony_dss.pl - Found at http://www.themonkeys.net/myth/sony_dss.pl
# 11.30.2003 Modifications By Michael Maley
# - Added explicit power_on call to ensure receiver is on for recording.
# - Added check_channel to prevent unnecessary channel change.
# Based on info from http://home.att.net/~mevenmo/sonydsscodes.html
$|=1;
use POSIX qw(:termios_h);
use FileHandle;
$verbose=0;
%pkt_decode=("0xF0" => "START PKT",
"0xF1" => "ERR 1",
"0xF2" => "GOT EXTENDED",
"0xF4" => "END PKT",
"0xF5" => "ERR 2",
"0xFB" => "PROMPT");
%terminal=("0xF1" => -1,
"0xF4" => 1,
"0xF5" => -1);
%keymap=(right => "0x9a",
left => "0x9b",
up => "0x9c",
down => "0x9d",
favorite => "0x9e",
select => "0xc3",
exit => "0xc5",
9 => "0xc6",
8 => "0xc7",
7 => "0xc8",
6 => "0xc9",
5 => "0xca",
4 => "0xcb",
3 => "0xcc",
2 => "0xcd",
1 => "0xce",
0 => "0xcf",
ch_up => "0xd2",
ch_dn => "0xd3",
power => "0xd5",
jump => "0xd8",
guide => "0xe5",
menu => "0xf7");
my $serial=init_serial("/dev/ttyS0","115200");
$ret=&change_channel(@ARGV);
exit(0);
sub change_channel {
my ($channel)=@_;
&power_on;
if ($channel != &check_channel) {
print ("Changing channel to $channel.\n") if ($verbose);
$_=sprintf("%4.4x",$channel);
($n1,$n2)=/(..)(..)/;
simple_command("0x46",$n1,$n2,"0x0");
}
}
sub power_on {
dss_command("0x02");
}
sub check_channel {
@currentChannel = dss_command("0x07");
print "Current Channel is: @currentChannel[0] \n" if ($verbose);
return (@currentChannel[0]);
}
sub simple_command {
if (defined(dss_command(@_))) {
return(1);
} else {
return(undef);
}
}
sub dss_command {
sendbytes("0xFA",@_);
return get_reply();
}
sub sendbytes {
(@send)=@_;
foreach (@send) { s/^0x//g; $_=hex($_); }
print "SEND: " if ($verbose);
foreach $num (@send) {
$str=pack('C',$num);
printf("0x%X [%s] ", $num, $str) if ($verbose);
syswrite($serial,$str,length($str));
}
print "\n" if ($verbose);
}
sub get_reply {
my $starttime=time();
my ($last,$ok,@ret);
print "RECV: " if ($verbose);
while (1) {
$ret=sysread($serial,$buf,1);
$str=sprintf("0x%2.2X", ord($buf));
# busy wait bad!
die ("Error ($str)\n") if (time() - $starttime >
;
next if $str eq "0x00";
if ($pkt_decode{$str}) {
print $str if ($verbose);
print "[$pkt_decode{$str}] " if ($verbose);
} else {
$_=$str; s/^0x//g; $_=hex($_);
printf("$str(%3.3s) ",$_) if ($verbose);
push (@ret,$_);
}
$ok=1 if ($terminal{$str} > 0);
last if ($terminal{$str});
last if ($last eq "0xFB" && $str eq "0xFB");
$last=$str;
}
print "\n\n" if ($verbose);
return @ret if ($ok);
return undef;
}
sub init_serial {
my($port,$baud)=@_;
my($termios,$cflag,$lflag,$iflag,$oflag);
my($voice);
my $serial=new FileHandle("+>$port") || die "Could not open $port: $!\n";
$termios = POSIX::Termios->new();
$termios->getattr($serial->fileno()) || die "getattr: $!\n";
$cflag= 0 | CS8 | HUPCL | CREAD | CLOCAL;
$lflag= 0;
$iflag= 0 | IGNBRK | IGNPAR | IXON | IXOFF;
$oflag= 0;
$termios->setcflag($cflag);
$termios->setlflag($lflag);
$termios->setiflag($iflag);
$termios->setoflag($oflag);
$termios->setattr($serial->fileno(),TCSANOW) || die "setattr: $!\n";
eval qq[
\$termios->setospeed(POSIX::B$baud) || die "setospeed: \$!\n";
\$termios->setispeed(POSIX::B$baud) || die "setispeed: \$!\n";
];
die $@ if $@;
$termios->setattr($serial->fileno(),TCSANOW) || die "setattr: $!\n";
# This gets rid of all the special characters..
$termios->getattr($serial->fileno()) || die "getattr: $!\n";
for (0..NCCS) {
if ($_ == NCCS) { last; }
# Dont mess up XON/XOFF..
if ($_ == VSTART || $_ == VSTOP) { next; }
$termios->setcc($_,0);
}
$termios->setattr($serial->fileno(),TCSANOW) || die "setattr: $!\n";
return $serial;
}
1;
I tried to run it from command prompt but I get a an error message saying bad interpreter: no such file or directory.
I have it copied to /usr/local/bin/sony0.pl.
I tested the cable and box in windows with DTVcon and changes channels fine. I had it connected to Com1. The script calls devttyS0