| LinHES Forums http://forum.linhes.org/ |
|
| PVR-150, please help http://forum.linhes.org/viewtopic.php?f=2&t=6292 |
Page 1 of 1 |
| Author: | gljubojevic [ Mon Oct 03, 2005 5:26 pm ] |
| Post subject: | PVR-150, please help |
Hi! I have followed instructions from: http://www.knoppmythwiki.org/index.php?page=HauppaugeOneFiftyInstallation Dowloaded and compiled latest ivtv drivers without success.. I see only noise in mythtv for about 1 second and than pictures freezes. I have also tryed tune channel manually and without success. Anyway my card is model 1051 PAL. Card is only detected propery (at least I think) when machine is cold booted, when rebooted card is detected as PVR-250. See ivtv from dmesg Code: root@mythtv:~# dmesg |grep ivtv tveeprom: ivtv version tveeprom: ivtv version msp34xx: ivtv version tuner (ivtv): chip found at addr 0xc2 i2c-bus bt878 #0 [sw] ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.9 (development svn snapshot revision ) loading ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: ivtv version ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] ivtv: i2c attach to card #0 ok [client=cx25840, addr=44] ivtv: i2c attach to card #0 ok [client=wm8775, addr=1b] ivtv: loading /lib/modules/ivtv-fw-enc.bin ivtv: Encoder revision: 0x02050032 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner: type set to 55 (TCL 2002MB) by ivtv i2c driver #0 ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv: i2c attach to card #0 ok [client=Hauppauge IR (PVR150), addr=71] Few things I don't understand 1.) Where to put (I have tryed in "/etc/modules.conf") Code: echo Loading IVTV drivers.
echo Unloading eeprom rmmod eeprom sleep 1 echo Loading tveeprom modprobe tveeprom sleep 1 echo Loading videodev modprobe videodev sleep 1 echo Loading cx25840 modprobe cx25840 i2c_enable=1 echo Loading tuner modprobe tuner sleep 1 echo Loading wm8775 modprobe wm8775 sleep 1 echo Loading ivtv modprobe ivtv 2.) What exactly should go in "/etc/mythtv/modules/ivtv" ? I have plain PVR-150 not MCE version. I also have plain BT878 card as /dev/video0 Is it even possible that PVR-150 can be autodetected correctly ? Thank you for all the help, im loosing sleep over this .. Goran |
|
| Author: | tjc [ Mon Oct 03, 2005 7:55 pm ] |
| Post subject: | |
Quote: ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!!
Have you tried installing the recommended version of the firmware mentioned in this message? For more info see: http://ivtv.writeme.ch/tiki-index.php?page=Drivers+and+Firmware |
|
| Author: | gljubojevic [ Tue Oct 04, 2005 2:16 am ] |
| Post subject: | update ... |
Thanks tjc but I have tried different firmwares and result was same. Anyway late last night i have managed to manually tune chanel and use mplayer to see feed from /dev/video1 Now the real question is why mythtv is unable to correctly tune to requested channel. Goran |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|