View unanswered posts    View active topics

Board index KnoppMyth Hardware

All times are UTC - 6 hours





Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
seano
PostPosted: Sat Jan 21, 2006 1:56 pm 
Offline
Joined: Fri Nov 25, 2005 10:22 pm
Posts: 73
Hello,

I'm trying to get my haupauge Silver remote that came with my pvr-150 with the reciever blaster cable working.

I'm running R5A30.1 with the updated IVTV 0.4.2.

I used these instructions to upgrade to 0.4.2:
http://knoppmythwiki.org/index.php?page=CompileIvtv

The card works fine. The remote still doesn't work.

To get the remote to work I've been using:
/usr/local/bin/lirc-reconfig.sh
-> 16 (Hauppauge) -> d (PVR-150)

Is this the correct script?

I think the key is in my /var/log/kern.log

Code:
Jan 21 11:37:17 mythtv kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jan 21 11:37:17 mythtv kernel: ivtv:  ==================== START INIT IVTV ====================
Jan 21 11:37:17 mythtv kernel: ivtv:  version 0.4.2 (tagged release) loading
Jan 21 11:37:17 mythtv kernel: ivtv:  Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
Jan 21 11:37:17 mythtv kernel: ivtv:  In case of problems please include the debug info between
Jan 21 11:37:17 mythtv kernel: ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
Jan 21 11:37:17 mythtv kernel: ivtv:  any module options, when mailing the ivtv-users mailinglist.
Jan 21 11:37:17 mythtv kernel: ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
Jan 21 11:37:17 mythtv kernel: ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
Jan 21 11:37:17 mythtv kernel: ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 21
Jan 21 11:37:17 mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
Jan 21 11:37:17 mythtv kernel: tveeprom: ivtv version
Jan 21 11:37:17 mythtv kernel: tveeprom: Hauppauge: model = 26052, rev = C199, serial# = 8165198
Jan 21 11:37:17 mythtv kernel: tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
Jan 21 11:37:17 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Jan 21 11:37:17 mythtv kernel: tveeprom: audio processor = CX25843 (type = 25)
Jan 21 11:37:17 mythtv kernel: tveeprom: decoder processor = CX25843 (type = 1e)
Jan 21 11:37:17 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
Jan 21 11:37:17 mythtv kernel: tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jan 21 11:37:17 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
Jan 21 11:37:18 mythtv kernel: cx25840 4-0044: ivtv driver
Jan 21 11:37:18 mythtv kernel: cx25840 4-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
Jan 21 11:37:20 mythtv kernel: cx25840 4-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
Jan 21 11:37:20 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
Jan 21 11:37:20 mythtv kernel: wm8775 4-001b: ivtv driver
Jan 21 11:37:20 mythtv kernel: wm8775 4-001b: chip found @ 0x36 (ivtv i2c driver #0)
Jan 21 11:37:20 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
Jan 21 11:37:20 mythtv kernel: tda9887 2-0043: (ivtv) chip found @ 0x86 (cx88[0])
Jan 21 11:37:20 mythtv kernel: tda9887 3-0043: (ivtv) chip found @ 0x86 (cx88[1])
Jan 21 11:37:21 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
Jan 21 11:37:21 mythtv kernel: ivtv0: Encoder revision: 0x02050032
Jan 21 11:37:21 mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
Jan 21 11:37:21 mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
Jan 21 11:37:21 mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
Jan 21 11:37:21 mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
Jan 21 11:37:21 mythtv kernel: tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
Jan 21 11:37:21 mythtv kernel: ivtv0: Initialized WinTV PVR 150, card #0
Jan 21 11:37:21 mythtv kernel: ivtv:  ====================  END INIT IVTV  ====================
Jan 21 11:37:21 mythtv kernel: lirc_pvr150: ivtv i2c driver #0: no devices found


No devices found?

Help!


Thanks Kindly,

Sean




[/code]
Top
 Profile  
 
kmkittre
 Post subject:
PostPosted: Tue Feb 07, 2006 9:24 am 
Offline
Joined: Tue Jul 12, 2005 8:01 am
Posts: 670
Location: Salem, MA
I'm not running a remote on an R5A30 install, but this is how I got the PVR-150 remote working on R5A16:

http://mysettopbox.tv/phpBB2/viewtopic.php?t=4609
Top
 Profile  
 
kmkittre
 Post subject:
PostPosted: Tue Feb 07, 2006 9:25 am 
Offline
Joined: Tue Jul 12, 2005 8:01 am
Posts: 670
Location: Salem, MA
Also, if you wanna take a look at my lircrc for this remote, you can get it here:

http://www.transmatrix.net/myth/lircrc

:D
Top
 Profile  
 
seano
 Post subject:
PostPosted: Tue Feb 07, 2006 10:44 am 
Offline
Joined: Fri Nov 25, 2005 10:22 pm
Posts: 73
Thanks!

I actually went and bought the MCE remote because of this issue. The MCE remote worked pretty much right out of the box.

-seano
Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 


Board index KnoppMyth Hardware

All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 20 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu