LinHES Forums
http://forum.linhes.org/

is Hauppauge Nova-S-Plus working?
http://forum.linhes.org/viewtopic.php?f=2&t=8146		 Page 1 of 1
Author:  kwbolte [ Sat Jan 28, 2006 10:46 am ]
Post subject:  is Hauppauge Nova-S-Plus working?
Hi everybody,

I own a Hauppauge Nova-S-Plus (for details see http://www.hauppauge.co.uk/pages/products/data_novasplus.html) and like to know if it works with the newest KnoppMyth.
The DVB drivers are out as you can see here: http://linuxtv.org/pipermail/linux-dvb/2005-November/006081.html and here: http://linuxtv.org/pipermail/linux-dvb/2005-December/006769.html.
But I didn't find anything in the KnoppMyth changelog.

Thanks and bye,
KAi
Author:  tjc [ Sat Jan 28, 2006 10:56 am ]
Post subject: 
Did you check the wiki and search the forum? I see some partial matches on the "WhatCardYouUse" page. However unless you can find a success story here I'd play it conservatively and look for a card that's known to work.
Author:  kwbolte [ Sat Jan 28, 2006 2:07 pm ]
Post subject: 
The "WhatCardYouUse"-Wiki-page does only list the Nova-S which is different from the Nova-S-Plus which contains additional IR and AV-in.

The drivers for the card are in the v4l-dvb drivers from linuxtv.org since december - but I don't know which version KnoppMyth uses.
Author:  cesman [ Sat Jan 28, 2006 8:28 pm ]
Post subject: 
If it was add to DVB in Nov of last years, then no. As the next release uses 2.6.15 then yes it should work...
Author:  Agonie [ Thu Feb 16, 2006 2:33 am ]
Post subject: 
Hi everybody, i just started to setup a mythbox for a friend of mine. It contains a Nova-S-Plus.
I installed Knoppmyth and only the analog part of the card was detected. The remote didn't work either.
So i grabbed the latest source snapshot from http://linuxtv.org/hg/v4l-dvb , compiled the modules and installed them (i have to comment out the cinergyT2 because compiling breaks at some point for this module). After a reboot the DVB Part was detected and the also remote works fine.
Can't say much about the channel setup, but I will test it tomorrow. Hope that helps.
Cheers Jan
Author:  Agonie [ Sat Feb 25, 2006 4:19 am ]
Post subject: 
Back again ...
The card works fine here with the new drivers. The only additional thing to mention is that there is NO DiseqC support available from the linux drivers. (but there is a patch somwhere at the dvb mailinglist) So with some additional work you can make the card work with Knoppmyth.

Greets Jan
Author:  kwbolte [ Sun Mar 19, 2006 7:39 am ]
Post subject:  HowTo Wiki started
Hey,

I started a Wiki HowTo get it working with R5B7:
http://wiki.knoppmyth.net/index.php?page=NovaSPlusHowTo

Feel free to add your comments.

KAi
Author:  kwbolte [ Sun Mar 19, 2006 8:58 am ]
Post subject:  remote
Agonie wrote:
So i grabbed the latest source snapshot from http://linuxtv.org/hg/v4l-dvb , compiled the modules and installed them (i have to comment out the cinergyT2 because compiling breaks at some point for this module). After a reboot the DVB Part was detected and the also remote works fine.

Can you tell me how you got the remote working? Which one did you choose in lirc-reconfig.sh ? Did you use the lirc that came with Knoppmyth or a newer one?
Only the four arrows and OK are working at mine. :-(
Author:  kwbolte [ Thu Mar 23, 2006 8:13 am ]
Post subject: 
I got it to work now, if somebody is having the same problems, take a look at my HowTo in the Wiki :

VVV
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/