| Author |
Message |
|
knappster
|
 Posted: Tue Dec 14, 2010 9:01 am |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
|
My wife finally did in the database by resetting the mythbox while it was running. Unfortunately my last backup was before I upgraded to 0.23 a little over a month ago. However, I had a clonezilla backup from just over a week ago so woohoo.
Everything is back and fine & dandy, except that when I look at my upcoming recordings, it is showing every episode of the programs I have configured instead of just the new episodes (I have the filter set to "exclude repeat episodes"). I have tried removing and recreating them to no avail. I see the same thing if I try to create a recording schedule for different programs as well.
Is this more likely to be a problem with the program data than the scheduled recording info? Would you recommend flushing the program data through mythfilldatabase and reinsert it?
Last edited by knappster on Sun Jan 02, 2011 3:21 pm, edited 1 time in total.
|
|
| Top |
|
 |
|
manicmike
|
Posted: Tue Dec 14, 2010 11:27 pm |
|
|
Joined: Sun Aug 28, 2005 7:07 pm
Posts: 821
Location:
Melbourne, Australia
|
|
It looks like your database doesn't have the "recorded programs" table populated correctly.
Is there any chance that your database skipped a table or two?
_________________
*********************
LinHES 7.4
Australian Dragon
*********************
|
|
| Top |
|
|
|
knappster
|
Posted: Wed Dec 15, 2010 9:40 am |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
I ran Code: mythfilldatabase --refresh-all and it appears to have cleared things up.
Unfortunately the corrupt database may have been a result of more than just a hard reset. I am having some issues where the playback will halt, looking at the errors.log I am seeing sata i/o errors (don't have the actual message in front of me now).
However, I checked the smartctl data and it showed no errors. I am wondering if it might be related to the motherboard instead, seeing as how this is the 2nd or 3rd hard drive where I have seen similar errors.
But at the same time I've noticed the hard drive will spin up, the activity LED will flash, then it will stall. Then after a few moments of silence it will repeat that. I'm not sure whether that could be caused by a fault on the motherboard or not.
When I had this problem in the past I tried a different SATA cable first and that didn't help. So I replaced the hard drive and the new one worked great for months. Interestingly enough I have had the old one in an external case for those same months and never had a problem with it.
Now I'm just rambling... I'll post exact error messages tonight.
|
|
| Top |
|
|
|
knappster
|
Posted: Wed Dec 15, 2010 6:12 pm |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
Here's a snippet of the errors.log file: Code: Dec 15 18:00:11 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:00:11 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:00:11 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:00:11 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:00:11 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:00:11 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:00:11 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:00:11 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:00:11 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:00:11 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:00:11 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:00:11 mythtv ata1.00: error: { UNC }
Dec 15 18:00:15 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:00:15 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:00:15 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:00:15 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:00:15 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:00:15 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:00:15 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:00:15 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:00:15 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:00:15 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:00:15 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:00:15 mythtv ata1.00: error: { UNC }
Dec 15 18:00:18 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:00:18 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:00:18 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:00:18 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:00:18 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:00:18 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:00:18 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:00:18 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:00:18 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:00:18 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:00:18 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:00:18 mythtv ata1.00: error: { UNC }
Dec 15 18:00:21 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:00:21 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:00:21 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:00:21 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:00:21 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:00:21 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:00:21 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:00:21 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:00:21 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:00:21 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:00:21 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:00:21 mythtv ata1.00: error: { UNC }
Dec 15 18:00:22 mythtv end_request: I/O error, dev sda, sector 15271615
Dec 15 18:05:04 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:04 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:04 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:04 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:04 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:04 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:04 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:04 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:04 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:04 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:04 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:04 mythtv ata1.00: error: { UNC }
Dec 15 18:05:07 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:07 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:07 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:07 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:07 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:07 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:07 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:07 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:07 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:07 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:07 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:07 mythtv ata1.00: error: { UNC }
Dec 15 18:05:11 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:11 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:11 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:11 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:11 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:11 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:11 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:11 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:11 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:11 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:11 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:11 mythtv ata1.00: error: { UNC }
Dec 15 18:05:14 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:14 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:14 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:14 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:14 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:14 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:14 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:14 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:14 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:14 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:14 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:14 mythtv ata1.00: error: { UNC }
Dec 15 18:05:17 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:17 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:17 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:17 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:17 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:17 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:17 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:17 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:17 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:17 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:17 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:17 mythtv ata1.00: error: { UNC }
Dec 15 18:05:21 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Dec 15 18:05:21 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Dec 15 18:05:21 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Dec 15 18:05:21 mythtv ata1: ATA_REG 0x41 ERR_REG 0x40
Dec 15 18:05:21 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Dec 15 18:05:21 mythtv ata1: tag 0x0: 1 1 0 1
Dec 15 18:05:21 mythtv ata1.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6 frozen
Dec 15 18:05:21 mythtv ata1.00: Ata error. fis:0x21
Dec 15 18:05:21 mythtv ata1.00: cmd 60/08:00:bf:06:e9/00:00:00:00:00/40 tag 0 ncq 4096 in
Dec 15 18:05:21 mythtv res 41/40:04:bf:06:e9/40:00:00:00:00/40 Emask 0x9 (media error)
Dec 15 18:05:21 mythtv ata1.00: status: { DRDY ERR }
Dec 15 18:05:21 mythtv ata1.00: error: { UNC }
Dec 15 18:05:22 mythtv end_request: I/O error, dev sda, sector 15271615 And here's the smartctl data: Code: sudo smartctl --all /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Second Generation Serial ATA family
Device Model: WDC WD3200AAKS-00L9A0
Serial Number: WD-WCAV25985807
Firmware Version: 01.03E01
User Capacity: 320,072,933,376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Dec 15 18:09:31 2010 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (6000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 73) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 174
3 Spin_Up_Time 0x0027 177 128 021 Pre-fail Always - 2133
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 752
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2896
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 738
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 502
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 752
194 Temperature_Celsius 0x0022 100 093 000 Old_age Always - 43
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 199 000 Old_age Always - 7
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
| Top |
|
|
|
manicmike
|
Posted: Thu Dec 16, 2010 4:14 pm |
|
|
Joined: Sun Aug 28, 2005 7:07 pm
Posts: 821
Location:
Melbourne, Australia
|
|
Do you think there might be an overheating problem inside your myth box? That would cause disks to have a very short life, and I'd suspect it as the primary cause of premature disk failure.
In case you're now wondering about this, simply removing dust will generally solve the problem. A scheduled hardware maintenance window may be a good idea, where you could whip out the vacuum cleaner and relieve your fans of their burden.
The failed disks usually come back to life if they failed because of this.
Mike
_________________
*********************
LinHES 7.4
Australian Dragon
*********************
|
|
| Top |
|
|
|
knappster
|
Posted: Thu Dec 16, 2010 4:38 pm |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
|
Definitely the hard drive... I had a RAID 1 in my desktop computer so I just pulled one of those drives out and popped it into the mythbox and it has been fine since. I was actually wondering about heat myself as it is in an entertainment center that is enclosed. I added 2 120mm fans to the entertainment center which one is blowing in at the bottom and the other out at the top.
I don't know how accurate the RRD data is, but it does not show the hdd temp exceeding about 47C and I just exchanged some e-mails with Western Digital tech support and he said it should be fine as long as it doesn't exceed 60C. I was somewhat concerned that it went from about 27-45 within an hour of startup, but he said that's ok. I may look into hard drive cooling anyway because I know that case gets stuffy.
I've hardly ever had hard drive failures in other computers and this is the 3rd time I've had a hard drive fail in this mythbox in 2.5 years. Of those 3, only the first one showed errors in the S.M.A.R.T. data.
|
|
| Top |
|
|
|
mattbatt
|
Posted: Thu Dec 16, 2010 8:51 pm |
|
|
Joined: Tue Aug 15, 2006 11:14 am
Posts: 1343
Location:
Orlando FL
|
|
It might be a better idea to have the one blow in and the other blow out at the top and to put a cheap air filter on the bottom one to keep dust down. They sell some foam type air filters for window unit air conditioners for like $5 that you can cut down to size or you could buy a 120mm air filter online.
_________________ My System
|
|
| Top |
|
|
|
knappster
|
Posted: Sun Jan 02, 2011 3:20 pm |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
I'm already having some problems pop up with this hard drive.
Quote: Jan 2 09:01:07 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x3 sactive 0x3
Jan 2 09:01:07 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x2 last_issue_tag 0x0
Jan 2 09:01:07 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Jan 2 09:01:07 mythtv ata1: ATA_REG 0x40 ERR_REG 0x0
Jan 2 09:01:07 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Jan 2 09:01:07 mythtv ata1: tag 0x0: 1 1 0 1
Jan 2 09:01:07 mythtv ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x1810000 action 0xe frozen
Jan 2 09:01:07 mythtv ata1.00: hot unplug
Jan 2 09:01:07 mythtv ata1: SError: { PHYRdyChg LinkSeq TrStaTrns }
Jan 2 09:01:07 mythtv ata1.00: cmd 60/40:00:57:b4:84/00:00:00:00:00/40 tag 0 ncq 32768 in
Jan 2 09:01:13 mythtv res 40/00:04:57:b4:84/00:04:57:b4:84/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/08:08:9f:b4:84/00:00:00:00:00/40 tag 1 ncq 4096 in
Jan 2 09:01:13 mythtv res 40/00:04:57:b4:84/00:04:57:b4:84/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1D sactive 0x1D
Jan 2 09:01:13 mythtv ata1: SWNCQ:qc_active 0x5 defer_bits 0x18 last_issue_tag 0x2
Jan 2 09:01:13 mythtv dhfis 0x5 dmafis 0x1 sdbfis 0x0
Jan 2 09:01:13 mythtv ata1: ATA_REG 0x40 ERR_REG 0x0
Jan 2 09:01:13 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Jan 2 09:01:13 mythtv ata1: tag 0x0: 1 1 0 0
Jan 2 09:01:13 mythtv ata1: tag 0x2: 1 0 0 1
Jan 2 09:01:13 mythtv ata1.00: exception Emask 0x10 SAct 0x1d SErr 0x1810000 action 0xe frozen
Jan 2 09:01:13 mythtv ata1.00: hot unplug
Jan 2 09:01:13 mythtv ata1: SError: { PHYRdyChg LinkSeq TrStaTrns }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/10:00:c7:14:7f/00:00:00:00:00/40 tag 0 ncq 8192 in
Jan 2 09:01:13 mythtv res 40/00:14:df:14:7f/00:14:df:14:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/10:10:df:14:7f/00:00:00:00:00/40 tag 2 ncq 8192 in
Jan 2 09:01:13 mythtv res 40/00:14:df:14:7f/00:14:df:14:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/28:18:ff:14:7f/00:00:00:00:00/40 tag 3 ncq 20480 in
Jan 2 09:01:13 mythtv res 40/00:14:df:14:7f/00:14:df:14:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/08:20:2f:15:7f/00:00:00:00:00/40 tag 4 ncq 4096 in
Jan 2 09:01:13 mythtv res 40/00:14:df:14:7f/00:14:df:14:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x2F sactive 0x2F
Jan 2 09:01:13 mythtv ata1: SWNCQ:qc_active 0x23 defer_bits 0xC last_issue_tag 0x1
Jan 2 09:01:13 mythtv dhfis 0x23 dmafis 0x20 sdbfis 0x0
Jan 2 09:01:13 mythtv ata1: ATA_REG 0x40 ERR_REG 0x0
Jan 2 09:01:13 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Jan 2 09:01:13 mythtv ata1: tag 0x0: 1 0 0 1
Jan 2 09:01:13 mythtv ata1: tag 0x1: 1 0 0 1
Jan 2 09:01:13 mythtv ata1: tag 0x5: 1 1 0 1
Jan 2 09:01:13 mythtv ata1.00: exception Emask 0x10 SAct 0x2f SErr 0x1910000 action 0xe frozen
Jan 2 09:01:13 mythtv ata1.00: hot unplug
Jan 2 09:01:13 mythtv ata1: SError: { PHYRdyChg Dispar LinkSeq TrStaTrns }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/48:00:ef:46:7f/00:00:00:00:00/40 tag 0 ncq 36864 in
Jan 2 09:01:13 mythtv res 40/00:0c:3f:47:7f/00:0c:3f:47:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/b0:08:3f:47:7f/00:00:00:00:00/40 tag 1 ncq 90112 in
Jan 2 09:01:13 mythtv res 40/00:0c:3f:47:7f/00:0c:3f:47:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/88:10:c7:68:7f/00:00:00:00:00/40 tag 2 ncq 69632 in
Jan 2 09:01:13 mythtv res 40/00:0c:3f:47:7f/00:0c:3f:47:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/20:18:87:69:7f/00:00:00:00:00/40 tag 3 ncq 16384 in
Jan 2 09:01:13 mythtv res 40/00:0c:3f:47:7f/00:0c:3f:47:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:13 mythtv ata1.00: cmd 60/30:28:df:62:7f/00:00:00:00:00/40 tag 5 ncq 24576 in
Jan 2 09:01:13 mythtv res 40/00:0c:3f:47:7f/00:0c:3f:47:7f/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:13 mythtv ata1.00: status: { DRDY }
Jan 2 09:01:34 mythtv ata1: EH in SWNCQ mode,QC:qc_active 0x1 sactive 0x1
Jan 2 09:01:34 mythtv ata1: SWNCQ:qc_active 0x1 defer_bits 0x0 last_issue_tag 0x0
Jan 2 09:01:34 mythtv dhfis 0x1 dmafis 0x1 sdbfis 0x0
Jan 2 09:01:34 mythtv ata1: ATA_REG 0x40 ERR_REG 0x0
Jan 2 09:01:34 mythtv ata1: tag : dhfis dmafis sdbfis sacitve
Jan 2 09:01:34 mythtv ata1: tag 0x0: 1 1 0 1
Jan 2 09:01:34 mythtv ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x1810000 action 0xe frozen
Jan 2 09:01:34 mythtv ata1.00: hot unplug
Jan 2 09:01:34 mythtv ata1: SError: { PHYRdyChg LinkSeq TrStaTrns }
Jan 2 09:01:34 mythtv ata1.00: cmd 60/80:00:8f:6e:ce/01:00:00:00:00/40 tag 0 ncq 196608 in
Jan 2 09:01:34 mythtv res 40/00:04:8f:6e:ce/00:04:8f:6e:ce/40 Emask 0x10 (ATA bus error)
Jan 2 09:01:34 mythtv ata1.00: status: { DRDY }
I wonder if it may be a power supply issue, because the hard drives seem okay in an external case. So I'm going to try replacing the power supply as it was included with the case and is 3-4 years old.
|
|
| Top |
|
|
|
manicmike
|
Posted: Tue Jan 04, 2011 3:51 pm |
|
|
Joined: Sun Aug 28, 2005 7:07 pm
Posts: 821
Location:
Melbourne, Australia
|
knappster wrote: I'm already having some problems pop up with this hard drive.
I wonder if it may be a power supply issue, because the hard drives seem okay in an external case. So I'm going to try replacing the power supply as it was included with the case and is 3-4 years old.
That's incredible, really. The PSU may be at fault. Make sure you replace it with a nice quiet one 
Also, if you can, get a UPS.
Mike
_________________
*********************
LinHES 7.4
Australian Dragon
*********************
|
|
| Top |
|
|
|
knappster
|
Posted: Tue Jan 04, 2011 9:50 pm |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
It's a microatx supply so I am somewhat limited on options 
However, I have one on the way from Newegg which should be here tomorrow or Thursday.
I've had a UPS installed for a couple of years now so I shouldn't have any problems with the incoming power.
Anyhow, I hope to have this resolved soon... so long as the new power supply isn't a dud... and so long as the new power supply doesn't fry everything in a blaze of glory.
|
|
| Top |
|
|
|
knappster
|
Posted: Wed Jan 05, 2011 10:11 pm |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
|
Just installed the new PSU, everything powered up and nothing started on fire. Time will tell how the hard drive behaves...
|
|
| Top |
|
|
|
knappster
|
Posted: Sat Jan 15, 2011 7:52 am |
|
|
Joined: Thu Sep 27, 2007 5:44 pm
Posts: 580
|
|
10 days after replacing the PSU and zero DVR issues (knock on wood). I think I FINALLY found the culprit.
|
|
| Top |
|
|
View unanswered posts
View active topics
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register
