LinHES Forums http://forum.linhes.org/ |
|
New Install of 7.3 - no video (sort of) [SOLVED] http://forum.linhes.org/viewtopic.php?f=22&t=22688 |
Page 1 of 1 |
Author: | bkamen [ Sat Aug 04, 2012 3:29 pm ] |
Post subject: | New Install of 7.3 - no video (sort of) [SOLVED] |
hey Cecil, I have a freshly burned CD of 7.3 I'm trying to install on an AMD based motherboard with an nVidia GT220 (or near) video card. It's hooked to a 42" Toshiba Regza TV via HDMI (on the TV) plugged into the DVI port of the video card. When the system boots, video properly shows up on the screen, but as the install boots, eventually the video just hangs. I think the VGA port of the card is being used at that point (I need to drag a VGA monitor into the same room as the TV to verify). BUT, I installed LinHES in the room WITH a VGA LCD... and it works. All the way through. Then, when I go back and plug in the now working system to the DVI/HDMI based LCD TV, the system just seems to loop at the yellow/blue LinHES screen starting it's starting up. I imagine this is a simple fix of sorts in the Xorg.conf (isn't it always?) -- but thought I would let you know since it doesn't "install out of the box" without needed some additional tweaking. Cheers, -Ben Additional info: the Video Card is only seeing the VGA monitor anyway and not the LCD via HDMI->DVI (derp) Code: [root@myth-fe1 X11]# nvidia-xconfig --query-gpu-info Number of GPUs: 1 GPU #0: Name : GeForce 210 PCI BusID : PCI:2:0:0 Number of Display Devices: 1 Display Device 0 (CRT-1): EDID Name : Samsung S/M 150MP Minimum HorizSync : 30.000 kHz Maximum HorizSync : 70.000 kHz Minimum VertRefresh : 56 Hz Maximum VertRefresh : 85 Hz Maximum PixelClock : 100.000 MHz Maximum Width : 1024 pixels Maximum Height : 768 pixels Preferred Width : 1024 pixels Preferred Height : 768 pixels Preferred VertRefresh : 60 Hz Physical Width : 300 mm Physical Height : 230 mm More info: If I switch the VGA monitor to the DVI port with an adapter and reboot the system, it can be detected as shown below. (note the CRT-# has changed) Code: [root@myth-fe1 ~]# nvidia-xconfig --use-edid --probe-all-gpus --query-gpu-info Number of GPUs: 1 GPU #0: Name : GeForce 210 PCI BusID : PCI:2:0:0 Number of Display Devices: 1 Display Device 0 (CRT-0): EDID Name : Samsung S/M 150MP Minimum HorizSync : 30.000 kHz Maximum HorizSync : 70.000 kHz Minimum VertRefresh : 56 Hz Maximum VertRefresh : 85 Hz Maximum PixelClock : 100.000 MHz Maximum Width : 1024 pixels Maximum Height : 768 pixels Preferred Width : 1024 pixels Preferred Height : 768 pixels Preferred VertRefresh : 60 Hz Physical Width : 300 mm Physical Height : 230 mm So, I guess the question is: the DVI->HDMI cable is like 10ft.. are there EDID detection problems common to these kinds of adapter cables? |
Author: | bkamen [ Sat Aug 04, 2012 9:26 pm ] |
Post subject: | Re: New Install of 7.3 - no video (sort of) [SOLVED] |
Well then... JUST for fun, I plugged the computer into HDMI-3 instead of HDMI-1 (TV has 3 ports) and look what nVidia reports NOW! Code: [root@myth-fe1 read-edid-1.4.2]# nvidia-xconfig --use-edid --probe-all-gpus --query-gpu-info
Number of GPUs: 1 GPU #0: Name : GeForce 210 PCI BusID : PCI:2:0:0 Number of Display Devices: 2 Display Device 0 (CRT-1): EDID Name : Samsung S/M 150MP Minimum HorizSync : 30.000 kHz Maximum HorizSync : 70.000 kHz Minimum VertRefresh : 56 Hz Maximum VertRefresh : 85 Hz Maximum PixelClock : 100.000 MHz Maximum Width : 1024 pixels Maximum Height : 768 pixels Preferred Width : 1024 pixels Preferred Height : 768 pixels Preferred VertRefresh : 60 Hz Physical Width : 300 mm Physical Height : 230 mm Display Device 1 (DFP-0): EDID Name : Toshiba TSB-TV Minimum HorizSync : 15.000 kHz Maximum HorizSync : 68.000 kHz Minimum VertRefresh : 23 Hz Maximum VertRefresh : 61 Hz Maximum PixelClock : 150.000 MHz Maximum Width : 1920 pixels Maximum Height : 1080 pixels Preferred Width : 1920 pixels Preferred Height : 1080 pixels Preferred VertRefresh : 60 Hz Physical Width : 1050 mm Physical Height : 590 mm |
Author: | Harveythedog [ Sun Aug 05, 2012 1:30 am ] |
Post subject: | Re: New Install of 7.3 - no video (sort of) [SOLVED] |
I have a Samsung LCD TV that does something similar, refuses to display anything but 60Hz on all it's HDMI ports except for HDMI 2, which has an edid with every mode you could ever want.... |
Author: | bkamen [ Mon Aug 20, 2012 1:07 pm ] |
Post subject: | Re: New Install of 7.3 - no video (sort of) [SOLVED] |
So it works on port2 as you'd expect? I'm curious to just configure Xorg.conf to what I want -- as the TV's speakers don't work with HDMI-2/3 -- only PC/HDMI-1 (shaking head) We've been inundated with (no so cheap) non-standards complaint gear. It's just shocking some days. -Ben |
Author: | Harveythedog [ Mon Aug 20, 2012 5:50 pm ] |
Post subject: | Re: New Install of 7.3 - no video (sort of) [SOLVED] |
My Samsung works on HDMI 2 like a champ! Has any mode I could ever want on there....all I ever needed to add in my Xorg.conf is: "1920x1080_50" and maybe set scaling to: Code: Option "FlatPanelProperties" "Scaling = Native" I guess you could try grabbing an edid.bin from the friendly port and try loading that in your Xorg.conf while running on a recalcitrant port?? The edid.bin from my TV's HDMI 2 http://members.wideband.net.au/htd/Hostedphotos/edid.bin Actually my brother has an awful,awful older LCD TV that has no info whatsoever on the only HDMI, I think I just forced that the old fashioned way with a PAL modeline. |
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |