There is a lot of good documentation on troubleshooting remotes but I am not able to figure out what is wrong with my system. I hope someone can give me a little help. This is driving me crazy.
I just did a fresh install of 8.3. In the LinHES Settings menu I have selected the remote to be "imon". This remote has a big, round button to move the cursor. Surrounding this big button is a ring of buttons that includes "enter" and "esc". I can use the big button to move up, down, left and right through the menus and to FF and REW in recordings. The enter and esc buttons also work fine.
Nothing else on the remote works. (play, pause, FF, REW, menu, etc.)
I used this page for troubleshooting.
http://linhes.org/projects/linhes/wiki/ ... on#remotesHere's some outputs from different commands.
Output from lsusb
Code:
Bus 005 Device 002: ID 15c2:0038 SoundGraph Inc. GD01 MX LCD Display/IR Receiver
Output from ir-keytables -t
Code:
Testing events. Please, press CTRL-C to abort.
1437348095.656715: event type EV_MSC(0x04): scancode = 0x2000029
1437348095.656715: event type EV_KEY(0x01) key_down: KEY_ESC(0x0001)
1437348095.656715: event type EV_SYN(0x00).
1437348095.792715: event type EV_KEY(0x01) key_up: KEY_ESC(0x0001)
1437348095.792715: event type EV_SYN(0x00).
1437348096.944730: event type EV_MSC(0x04): scancode = 0x2000028
1437348096.944730: event type EV_KEY(0x01) key_down: KEY_ENTER(0x0001)
1437348096.944730: event type EV_SYN(0x00).
1437348097.064736: event type EV_KEY(0x01) key_up: KEY_ENTER(0x0001)
1437348097.064736: event type EV_SYN(0x00).
1437348099.680772: event type EV_MSC(0x04): scancode = 0x2a8115b7
1437348099.680772: event type EV_KEY(0x01) key_down: KEY_PLAY(0x0001)
1437348099.680772: event type EV_SYN(0x00).
1437348099.816779: event type EV_KEY(0x01) key_up: KEY_PLAY(0x0001)
1437348099.816779: event type EV_SYN(0x00).
1437348101.760803: event type EV_MSC(0x04): scancode = 0x2a9115b7
1437348101.760803: event type EV_KEY(0x01) key_down: KEY_PAUSE(0x0001)
1437348101.760803: event type EV_SYN(0x00).
1437348101.880807: event type EV_KEY(0x01) key_up: KEY_PAUSE(0x0001)
1437348101.880807: event type EV_SYN(0x00).
MythTV responds to the enter and esc keys but not to the play and pause keys.
Output of ir-keytable:
Code:
Found /sys/class/rc/rc0/ (/dev/input/event8) with:
Driver imon, table rc-imon-pad
Supported protocols: RC-6 other
Enabled protocols: other
Name: iMON Remote (15c2:0038)
bus: 3, vendor/product: 15c2:0038, version: 0x0002
Repeat delay = 500 ms, repeat period = 125 ms
/etc/rc_keymaps/ is empty. This seems strange because ir-keytables -t recognizes all of the input signals and lists the key name for them.
I see three locations for the lircrc file. They all have the same contents (/etc/lircrc /home/mythtv/.lircrc and /home/mythtv/.mythtv/lircrc)
Code:
include "/usr/MythVantage/templates/remotes/other/imon/lircrc"
Here are some relevant sections of the MythVantage lircrc
Code:
# Pause playback
begin
prog = mplayer
button = KEY_PAUSE
config = pause
end
# If paused, resume playing
begin
prog = mplayer
button = KEY_PLAY
config = pause
end
There is no response when I run irw and press remote buttons
Also, there is no response when I run ircat mythtv and press remote buttons. Even for the enter and esc buttons that actually do something in MythTV.
I had this all working under LinHES 7.?? but don't have any backup of the config files. I've been tinkering with this for a while and I am stumped. As I understand this, all or nothing should be working but it's not like that. Anyone have any thoughts on things to try?