LinHES Forums http://forum.linhes.org/ |
|
[SOLVED] PVR-350 Init Issues http://forum.linhes.org/viewtopic.php?f=23&t=20760 |
Page 1 of 1 |
Author: | bkamen [ Sun Jan 10, 2010 2:45 pm ] |
Post subject: | [SOLVED] PVR-350 Init Issues |
EDIT: This is well covered elsewhere as just being a UDEV problem on init with various methods to fix. So I'm going to close this topic out rather than delete it. Occassionally, when MythTV starts up, my PVR-350 doesn't init. So I have to reboot until it does. Although this morning it seems pretty stubborn not to want to start... DMESG says: Code: ivtv: Start initialization, version 1.4.0
ivtv0: Initializing card #0 ivtv0: Autodetected Hauppauge card (cx23415 based) ivtv 0000:02:04.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom 2-0050: Hauppauge model 48132, rev K268, serial# 2927118 tveeprom 2-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is MSP4448 (idx 27) tveeprom 2-0050: decoder processor is SAA7115 (idx 19) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-350 nvidia: module license 'NVIDIA' taints kernel. PPP generic driver version 2.4.2 cx88/0: cx2388x v4l2 driver version 0.0.6 loaded ppdev: user-space parallel port driver saa7115 2-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) saa7127 2-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) msp3400 2-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 2-0040: msp3400 supports radio, mode is autodetect and autoselect tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 2-0043: creating new instance tda9887 2-0043: tda988[5/6/7] found tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) tuner-simple 2-0061: creating new instance tuner-simple 2-0061: type set to 47 (LG NTSC (TAPE series)) ivtv0: Registered device video0 for encoder MPG (4096 kB) ivtv0: Registered device video32 for encoder YUV (2048 kB) ivtv0: Registered device vbi0 for encoder VBI (1024 kB) ivtv0: Registered device video24 for encoder PCM (320 kB) ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPG (1024 kB) ivtv0: Registered device vbi8 for decoder VBI (64 kB) ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV (1024 kB) ivtv0: Initialized card #0: Hauppauge WinTV PVR-350 cx8800 0000:02:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 cx88[0]/0: found at 0000:02:06.0, rev: 5, irq: 22, latency: 32, mmio: 0xf4000000 cx88[0]/0: registered device video1 [v4l2] cx88[0]/0: registered device vbi1 cx88[0]/0: registered device radio1 ivtv: End initialization I noticed that it might have something to do with when I set up the card.. it was pointing to /dev/video1 which was the PVR-350, and then on reboot, it seems it's now /dev/video0.. which when I change it - fixes the problem. So possibly I need to tell the drivers on startup to assign cardX with /dev/videoX and not let them possibly switch. Hmmmm... -Ben |
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |