View unanswered posts    View active topics

All times are UTC - 6 hours





Post new topic Reply to topic  [ 3 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
PostPosted: Sat Jun 05, 2010 11:22 pm 
Offline
Joined: Sat Apr 21, 2007 6:55 pm
Posts: 306
Location: CA,USA
Hi all,

I am running R6.02. Have an SBE with a KWorld 115 which works great. Added a hauppauge PVR-150 (well, 2 actually) and thought it would be fairly easy to get them to work - no such luck. I defined one of them as a capture card, connected it to a video source but I do not get the channels listed in the EPG. Plus I can't switch to that card while watching LiveTV, I'm simply stuck with the kworld 115. Logs look good as below AFAICT but when I go to the myth frontend on the SBE it does say "Tuner 72 has an error". But how can I figure out what the error is?

"dmesg | grep -i error" returns nothing.
Errors.log is blank.
I don't see anything obviously bad in mythbackend.log

Quote:
[root@sbe log]# dmesg | grep -i ivtv
ivtv: Start initialization, version 1.4.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:05:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ivtv0: Autodetected Hauppauge WinTV PVR-150
cx25840 1-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
ivtv1: Initializing card #1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:05:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ivtv1: Autodetected Hauppauge WinTV PVR-150
ivtv1: Reopen i2c bus for IR-blaster support
cx25840 3-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1)
wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: Registered device video2 for encoder MPG (4096 kB)
ivtv1: Registered device video34 for encoder YUV (2048 kB)
ivtv1: Registered device vbi2 for encoder VBI (1024 kB)
ivtv1: Registered device video26 for encoder PCM (320 kB)
ivtv1: Initialized card #1: Hauppauge WinTV PVR-150
ivtv: End initialization
ivtv 0000:05:04.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
ivtv 0000:05:09.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Encoder revision: 0x02060039

_________________
Paul O'Flynn


Last edited by poflynn on Sun Jun 06, 2010 10:40 pm, edited 1 time in total.


Top
 Profile  
 
 Post subject:
PostPosted: Sun Jun 06, 2010 1:31 pm 
Offline
Joined: Wed Jan 07, 2004 12:14 pm
Posts: 402
Location: Charlotte, NC
Make sure you define it as an "IVTV MPEG-2 encoder card". Then assign the analog video source (I am assuming you have cable) and re-scan channels.


Top
 Profile  
 
 Post subject:
PostPosted: Sun Jun 06, 2010 10:39 pm 
Offline
Joined: Sat Apr 21, 2007 6:55 pm
Posts: 306
Location: CA,USA
I noticed the capture card type descr had changed from R5 ok, but I had guessed the one you mentioned.

For fun I switched it to use the SVIDEO i/p, rebooted, switched it back to "Tuner 1", rebooted again and now it works! What the heck? I have no idea what happened but I ain't complaining!

Thx for the reply.

_________________
Paul O'Flynn


Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 


All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu