| LinHES Forums http://forum.linhes.org/ |
|
| Added a PVR-150 to my system, won't work - SOLVED http://forum.linhes.org/viewtopic.php?f=23&t=21109 |
Page 1 of 1 |
| Author: | poflynn [ Sat Jun 05, 2010 11:22 pm ] |
| Post subject: | Added a PVR-150 to my system, won't work - SOLVED |
Hi all, I am running R6.02. Have an SBE with a KWorld 115 which works great. Added a hauppauge PVR-150 (well, 2 actually) and thought it would be fairly easy to get them to work - no such luck. I defined one of them as a capture card, connected it to a video source but I do not get the channels listed in the EPG. Plus I can't switch to that card while watching LiveTV, I'm simply stuck with the kworld 115. Logs look good as below AFAICT but when I go to the myth frontend on the SBE it does say "Tuner 72 has an error". But how can I figure out what the error is? "dmesg | grep -i error" returns nothing. Errors.log is blank. I don't see anything obviously bad in mythbackend.log Quote: [root@sbe log]# dmesg | grep -i ivtv
ivtv: Start initialization, version 1.4.0 ivtv0: Initializing card #0 ivtv0: Autodetected Hauppauge card (cx23416 based) ivtv 0000:05:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ivtv0: Autodetected Hauppauge WinTV PVR-150 cx25840 1-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0) tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPG (4096 kB) ivtv0: Registered device video32 for encoder YUV (2048 kB) ivtv0: Registered device vbi0 for encoder VBI (1024 kB) ivtv0: Registered device video24 for encoder PCM (320 kB) ivtv0: Registered device radio0 for encoder radio ivtv0: Initialized card #0: Hauppauge WinTV PVR-150 ivtv1: Initializing card #1 ivtv1: Autodetected Hauppauge card (cx23416 based) ivtv 0000:05:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ivtv1: Autodetected Hauppauge WinTV PVR-150 ivtv1: Reopen i2c bus for IR-blaster support cx25840 3-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1) tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) ivtv1: Registered device video2 for encoder MPG (4096 kB) ivtv1: Registered device video34 for encoder YUV (2048 kB) ivtv1: Registered device vbi2 for encoder VBI (1024 kB) ivtv1: Registered device video26 for encoder PCM (320 kB) ivtv1: Initialized card #1: Hauppauge WinTV PVR-150 ivtv: End initialization ivtv 0000:05:04.0: firmware: requesting v4l-cx2341x-enc.fw ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 ivtv 0000:05:09.0: firmware: requesting v4l-cx2341x-enc.fw ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv1: Encoder revision: 0x02060039 |
|
| Author: | nbdwt73 [ Sun Jun 06, 2010 1:31 pm ] |
| Post subject: | |
Make sure you define it as an "IVTV MPEG-2 encoder card". Then assign the analog video source (I am assuming you have cable) and re-scan channels. |
|
| Author: | poflynn [ Sun Jun 06, 2010 10:39 pm ] |
| Post subject: | |
I noticed the capture card type descr had changed from R5 ok, but I had guessed the one you mentioned. For fun I switched it to use the SVIDEO i/p, rebooted, switched it back to "Tuner 1", rebooted again and now it works! What the heck? I have no idea what happened but I ain't complaining! Thx for the reply. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|