LinHES Forums
http://forum.linhes.org/

Twinhan DVB-S card?
http://forum.linhes.org/viewtopic.php?f=5&t=7807		 Page 1 of 1
Author:  stephencu2004 [ Tue Jan 10, 2006 9:32 am ]
Post subject:  Twinhan DVB-S card?
I searched the forum and could not find a strait answer as to whether the Twinhan DVB-S card has been sucessfully installed on knoppMyth to work with a few satellites and a Diseq switch. I would like to try to get this setup with Telstar 5 and Galaxy G10R if anyone has any input on this type of setup please chime in.

Thanks,
Stephen :wink:
Author:  Girkers [ Tue Jan 10, 2006 4:52 pm ]
Post subject: 
You may be better suited at searching for the chipset on the card. I use the Twinhan DVB-T card and it works fine, don't know if that really helps :?
Author:  stephencu2004 [ Thu Jan 12, 2006 1:20 pm ]
Post subject: 
Thank you for your reply Girkers I have read on a different forum that the DVB-s cards are still a little flaky with Myth but are working better in the newest version of myth SVR (or something like that). I will keep searching for an answer and might just give it a try to see if I can get it to work with KnoppMyth. If I figure something out I will post my results.....

Thanks again
Author:  sabre66 [ Thu Jan 12, 2006 8:02 pm ]
Post subject: 
In my "development" box I'm using a Twinhan 102g and installing the latest svn every 2 days , and so far its working great . Also please take note in my dev box I'm using Gentoo . I tried using knoppmyth fþ“ïÛt but ran into too many problems .
Author:  stephencu2004 [ Sat Jan 14, 2006 12:42 pm ]
Post subject: 
sabre66 thanks for the info I am going to try it with KM first if I can't figure it out I will try Gentoo :shock:

I have another question, can Myth drive an H2H motor so I can grab multiple sats?
Author:  sabre66 [ Wed Jan 18, 2006 6:57 pm ]
Post subject: 
stephencu2004 wrote:
sabre66 thanks for the info I am going to try it with KM first if I can't figure it out I will try Gentoo :shock:

I have another question, can Myth drive an H2H motor so I can grab multiple sats?


No problem ......As for the motor I don't know for sure I saw a patch but I'm not sure I'd be allowed to post it here , hell I'll pm it to you.
Author:  stephencu2004 [ Thu Jan 19, 2006 9:30 am ]
Post subject: 
sabre66 wrote:
stephencu2004 wrote:
sabre66 thanks for the info I am going to try it with KM first if I can't figure it out I will try Gentoo :shock:

I have another question, can Myth drive an H2H motor so I can grab multiple sats?


No problem ......As for the motor I don't know for sure I saw a patch but I'm not sure I'd be allowed to post it here , hell I'll pm it to you.


Thank you again fine sir, just as an update KnoppMyth works great with a Twinhan VP1020A DVB-S card right out of the box. I am still trying to get the motor to respond but I was able to get G10r which has my favorite free music channel "TubeTV" so for now I am very happy an still looking into the motor with USALS.

Thanks to all :P
Author:  rodstickman [ Mon Aug 21, 2006 4:24 pm ]
Post subject: 
stephencu2004 wrote:
sabre66 wrote:
stephencu2004 wrote:
sabre66 thanks for the info I am going to try it with KM first if I can't figure it out I will try Gentoo :shock:

I have another question, can Myth drive an H2H motor so I can grab multiple sats?


No problem ......As for the motor I don't know for sure I saw a patch but I'm not sure I'd be allowed to post it here , hell I'll pm it to you.


Thank you again fine sir, just as an update KnoppMyth works great with a Twinhan VP1020A DVB-S card right out of the box. I am still trying to get the motor to respond but I was able to get G10r which has my favorite free music channel "TubeTV" so for now I am very happy an still looking into the motor with USALS.

Thanks to all :P



I am trying to get a fresh install working with a twinhan 102g

Everything seems to go well until I start searching for channels.

What parameters do I need to enter for the search? For now i have a single LNB pointed to echo* 1 @ 148.

I get a good signal using my dish box, but when I try to find anything the channel search hangs up at 3 percent.
Author:  daverfw [ Sun Sep 24, 2006 1:35 pm ]
Post subject: 
rodstickman wrote:
stephencu2004 wrote:
sabre66 wrote:
stephencu2004 wrote:
sabre66 thanks for the info I am going to try it with KM first if I can't figure it out I will try Gentoo :shock:

I have another question, can Myth drive an H2H motor so I can grab multiple sats?


No problem ......As for the motor I don't know for sure I saw a patch but I'm not sure I'd be allowed to post it here , hell I'll pm it to you.


Thank you again fine sir, just as an update KnoppMyth works great with a Twinhan VP1020A DVB-S card right out of the box. I am still trying to get the motor to respond but I was able to get G10r which has my favorite free music channel "TubeTV" so for now I am very happy an still looking into the motor with USALS.

Thanks to all :P



I am trying to get a fresh install working with a twinhan 102g

Everything seems to go well until I start searching for channels.

What parameters do I need to enter for the search? For now i have a single LNB pointed to echo* 1 @ 148.

I get a good signal using my dish box, but when I try to find anything the channel search hangs up at 3 percent.


i run into the same issue where it hangs at 3% using the same card any solution?
Author:  steve909 [ Mon Sep 25, 2006 8:28 pm ]
Post subject: 
Hello.
Re hanging at 3%, I'm sure I had the same problem, I can't properly recall how I got past it but have you tried hitting ALT+TAB at that point to bring up the terminal? I think it may be waiting for a response from you. Can't guarantee thats the answer, I'm going from memory, and was trying everything as each problem came up, so may be getting mixed up!
All the best.
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/