First off, thanks to Cecil again. Everything during my upgrade went very well!

... with the exception of the PVR-350's IR receiver. I have a blaster as well, so I thought the confusion was between /dev/lirc and /dev/lirc1. IRBLASTER is quite happy to operate on /dev/lirc without issues.

I can't for the life of me get the 350's receiver functioning as it did before the upgrade. My /etc/lirc/lircd.conf and ~mythtv/.mythtv/lircrc are good, as I've tested them on the frontend upstairs with a homebrew receiver... no issues. IRW on the box doesn't yield any results either.



What is the verdict on getting this beast to work ? Do I need to use the LIRC_pvr_150 source kit to compile ? IF so, do I need to select the 'Hauppauge 150' option, or just 'Hauppauge TV Card' ?

Thanks in advance,
Greg.

Just following up. I followed the instructions for the LIRC (pvr 150) kit, and still no go. Can someone comment on what they needed to do with R5B7 to get their IR Receiver on the 350 working ?

Thanks,
Greg.

I have the same card. The first install it would work either. Second install it worked out of the box.

Now for the blaster, I dont know about this but I was never able to get the script to work correctly, and I dont think anyone else was able to either.

Use the ledxmit posting on this forum to get the blaster to work. Takes about 5 minutes..

Hope this helps

_________________
Once you go HDTV, you'll never come back!

That's the kicker.. I got the IRBlaster stuff working in about 10 minutes. Yanked the 3100 config from the lirc site, and away I went.

What steps did you take to use the onboard IR receiver on the 350 ?

Thanks.

With me it was fairly simple , I have the Hauppauge A415-HPG (look under battery)
remote for the 350.

Found this for my remote: copied it to /etc/lirc/lircd.conf and restarted lircd and the frontend
and I was good to go. You may have fix up your ~mythtv/.lircrc to fix some of your
key mappings.

======== Lircd.conf A415-HPG =============

# original Hauppauge TV cards !!!
#

#
# this config file was automatically generated
# using lirc-0.7.0(any) on Sun Nov 28 20:25:09 2004
#
# contributed by
#
# brand: Hauppauge 350
# Created: G.J. Werler (The Netherlands)
# Project: Mythtv Fedora Pundit-R www.mythtvportal.com
# Date: 2004/11/28
# model no. of remote control: Hauppauge A415-HPG
# devices being controlled by this remote: PVR-350
#

begin remote

name Hauppauge_350
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100

one 969 811
zero 969 811
plead 1097
gap 114605
toggle_bit 2


begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes

end remote

==================

Thanks for the suggestion. I'm still not seeing anything via 'irw' though, and restarting lirc and the frontend afterwards doesn't yield a workable remote.

My lircd.conf worked with the 350 in R5A16... would anything have changed on that front ?

I'm worried that my mucking with the pvr_150 kit might have screwed a few files up.. short of the reinstall, is there a way to get the 'stock knoppmyth' lirc stuff back in ? dpkg -L lirc seems to give me the list of files.. that might work

Can anyone confirm having this issue as well, or is it just me ?

Greg.

I didn't see anything with irw after my auto-upgrade (prv-350).
I was only after the bit of messing with conf's that I started to work..

On a side note.. Is your ff/Rew working correctly?

Will try again tonight and see if there are any problems. Are you referring to livetv ?

Either liveTv or a recording. I am just wondering if the bug described below affects all 350's

http://mysettopbox.tv/phpBB2/viewtopic.php?t=9157

The gist of it is, the video freezes on the screen with ff/rew with all speeds except 3x ff.

Ahh, I'm not using the tv-out on the 350. Would love to, but moved to a GF4 440-MX to handle DVD and AVI output before they got better with the XV stuff.

Greg.

UPDATE:

Pulled the LIRC 0.8.0 kit from lirc.org, compiled with Hauppauge TV card support, did a make install, all is well. Not sure what the issue was, but it's all working.

Thanks for all the suggestions.

Greg.