| LinHES Forums http://forum.linhes.org/ |
|
| Analog VCR AV as Input Channel - with PVR350 http://forum.linhes.org/viewtopic.php?f=6&t=9971 |
Page 1 of 1 |
| Author: | smtm [ Mon May 08, 2006 8:39 am ] |
| Post subject: | Analog VCR AV as Input Channel - with PVR350 |
Good Afternoon Has anybody figured out how to get the get a analog VCR AV channel as a channel in mythtv (using a PVR-350 Card)?. I would loop the antenna cable through the VCR. It is probably just a question of knowing which frequencey to set in the mythtv-setup programm. |
|
| Author: | cesman [ Tue May 09, 2006 10:02 pm ] |
| Post subject: | |
I believe there is a post or two on the forum. I know various exist on the mythtv mailing list. http://www.gossamer-threads.com/lists/mythtv/users |
|
| Author: | smtm [ Mon May 15, 2006 6:19 am ] |
| Post subject: | |
Hi i did some search and found that there is talk of tuning to channel 2 or 3. Is there a certain (maybe dummy-) frequency associated with the VCR output. I do have my analog antenna cable looped through the VCR, so it should not be the issue of not having the signal from the VCR. I am also aware that it will have to be a manual recording from within mythtv. Any hints? |
|
| Author: | jorin [ Mon May 15, 2006 6:59 am ] |
| Post subject: | |
I've noticed that my stand alone DVD recorder sends out a bad signal when using the Coax out when connected to a TVs Antenna in. Except for channel 3/4 which is what you would be watching on the VCR. If this is what you are palnning you may want to test it. You could add a splitter before the VCR and send one to it and the other to the PVR-350. Are you recording from tape? You would want to use s-video in or at least composite for best picture. That way you don't have to mess with the coax cabling. |
|
| Author: | smtm [ Tue May 16, 2006 3:08 am ] |
| Post subject: | |
Do you mean I shoud use a scart cable on the VCR side and a S-Video input on the PVR-350 side? And then setup another "Tuner" in mythtv-setup as "composite? What would the channel setting be (frequency) of that composite source?. Btw, I find it quite confusing to figure out where mythtv places the channel settings (ie. What to specify:Either channel frequceny or if inputting channel names, where the frequencies are stored that are used to map to the chennel names (I am in PAL europe-west/austria channel names would be E7,E8 - not the actual station callsigns). |
|
| Author: | jorin [ Tue May 16, 2006 9:36 pm ] |
| Post subject: | |
I just read up a little on SCART, sounded familiar but have no dealings with it. I suppose you can get an adapter to go from SCART to S-Video? If you can use this first for best posible quality. http://en.wikipedia.org/wiki/SCART I know you can go into myth-setup and configure the card to use its other inputs. You won't use the input as a tuner but as another source. You will see it once you get there. I've not used the card this way before. Someone else may be able to answer this? |
|
| Author: | mjl [ Tue May 16, 2006 10:33 pm ] |
| Post subject: | |
Hi, Dig around in the forum as there has been discussions in regard to using the composite input. Here is one sample. http://mysettopbox.tv/phpBB2/viewtopic. ... a732#54599 Mike |
|
| Author: | jorin [ Wed May 17, 2006 5:12 pm ] |
| Post subject: | |
There should be some info for users that connect satellite/cable settop boxes to their Myth boxes. Since they can't tune Encrypted stations the way to get it into the box is through those other inputs. |
|
| Author: | smtm [ Fri May 19, 2006 2:51 am ] |
| Post subject: | |
SOLVED: I got it working. Here is what I did: Cabeling: I used the scart cable provided by the hauppauge 350 (pal) version and attached it to the composite input at the rear of the 350 card and on my vcr it is attached to the SCART jack, that previously went to the TV. Setup in mythtv with mythtv-setup * Added another video source "VCR" (where you normally link to epg data) * Linked the "VCR" source to composite-3 of the PVR350 * Set up a channel called VCR on Position 100 on channel 3 (I did this because in some of the threads that were posted there were some statements that it would only work with channel 3) Switched on mythfrontend and it worked straight away Thanx for all the input |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|