Installed 6.02 recently. My hauppage pvr-150 grey remote works perfectly, but i'm having trouble getting the IR blaster to do anything. I see this in the lirc logs:
Code:
lircd: accepted new client on /dev/lircd
lircd: error processing command: SEND_ONCE blaster 2
lircd: hardware does not support sending
lircd: removed client
I copied my channel change script from my old r5.5 system. It is basically doing this:
Code:
irsend SEND_ONCE blaster 2
/var/log/messages has:
Code:
Jun 5 16:48:41 mythtv lirc_dev: IR Remote Control driver registered, major 61
Jun 5 16:48:41 mythtv bttv: driver version 0.9.17 loaded
Jun 5 16:48:41 mythtv bttv: using 8 buffers with 2080k (520 pages) each for cap
ture
Jun 5 16:48:41 mythtv ivtv: Start initialization, version 1.4.0
Jun 5 16:48:41 mythtv ivtv0: Initializing card #0
Jun 5 16:48:41 mythtv ivtv0: Autodetected Hauppauge card (cx23416 based)
Jun 5 16:48:41 mythtv ivtv 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jun 5 16:48:41 mythtv ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
Jun 5 16:48:41 mythtv tveeprom 0-0050: Hauppauge model 26152, rev C599, serial# 8958264
Jun 5 16:48:41 mythtv tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
Jun 5 16:48:41 mythtv tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
Jun 5 16:48:41 mythtv tveeprom 0-0050: audio processor is CX25843 (idx 37)
Jun 5 16:48:41 mythtv tveeprom 0-0050: decoder processor is CX25843 (idx 30)
Jun 5 16:48:41 mythtv tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter
Jun 5 16:48:41 mythtv ivtv0: Autodetected Hauppauge WinTV PVR-150
Jun 5 16:48:41 mythtv ivtv0: Reopen i2c bus for IR-blaster support
Jun 5 16:48:41 mythtv cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
Jun 5 16:48:41 mythtv tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Jun 5 16:48:41 mythtv wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
Jun 5 16:48:41 mythtv tuner-simple 0-0061: creating new instance
Jun 5 16:48:41 mythtv tuner-simple 0-0061: type set to 50 (TCL 2002N)
Jun 5 16:48:41 mythtv ivtv0: Registered device video0 for encoder MPG (4096 kB)
Jun 5 16:48:41 mythtv ivtv0: Registered device video32 for encoder YUV (2048 kB)
Jun 5 16:48:41 mythtv ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
Jun 5 16:48:41 mythtv ivtv0: Registered device video24 for encoder PCM (320 kB)
Jun 5 16:48:41 mythtv ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
Jun 5 16:48:41 mythtv ivtv: End initialization
Jun 5 16:48:41 mythtv cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
Jun 5 16:48:41 mythtv lirc_i2c: chip 0x10020 found @ 0x71 (Hauppauge PVR150)
Jun 5 16:48:41 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10
What does the '
Reopen i2c bus for IR-blaster support' message mean?
Any ideas of things I can try?
lsmod|grep lirc
Code:
lirc_imon 18056 1
usbcore 136848 4 lirc_imon,uhci_hcd,ehci_hcd
lirc_i2c 10756 1
lirc_dev 13492 2 lirc_imon,lirc_i2c
i2c_core 22804 38 i2c_viapro,nvidia,wm8775,cx25840,tuner,tea5767,tda8290,tda18271,tda827x,mt20xx,tea5761,ivtv,bttv,v4l2_common,lirc_i2c,cx88_vp3054_i2c,mt352,cx88xx,i2c_algo_bit,tveeprom,tuner_xc2028,s5h1409,xc5000,dvb_pll,s5h1411,or51132,cx24116,nxt200x,isl6421,stb6000,tda9887,tuner_simple,zl10353,cx24123,lgdt330x,stv0299,stv0288,cx22702