| Author |
Message |
|
pairajacks
|
 Posted: Sun Jan 21, 2007 11:50 am |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
|
Can't figure out why this appears to be working, but no light blinking:
root@mythtv:/usr/local/bin# change_channel 200
channel changing 200
1. The change_channel script is unchanged from the instructions, and is in /usr/local/bin
2. I think my lircd.conf file (below) is correct and permissions wide open
root@mythtv:/etc# ls -alt lircd.conf
lrwxrwxrwx 1 root root 20 Jan 13 14:39 lircd.conf -> /etc/lirc/lircd.conf
3. The send_power_new makes the light blink
My lircd.conf file in /etc:
begin remote
name blaster
bits 32
flags RAW_CODES
eps 0
aeps 0
plead 0
gap 333333
repeat_bit 0
begin raw_codes
name 0
2149318656
name 1
2149318657
name 2
2149318658
name 3
2149318659
name 4
2149318660
name 5
2149318661
name 6
2149318662
name 7
2149318663
name 8
2149318664
name 9
2149318665
name POWER
2149318666
name CH_UP
2149318671
name CH_DOWN
2149318672
name MUTE
2149318673
name VOL_DOWN
2149318674
name CH_PREVIOUS
2149318675
name VOL_UP
2149318676
name DISPLAY
2149318677
name EXIT
2149318680
name GUIDE
2149318683
name SELECT
2149318686
name AV
2149318697
name ENTER
2149318699
name MENU
2149318703
name MUP
2149318704
name MDOWN
2149318705
name MLEFT
2149318706
name MRIGHT
2149318707
end raw_codes
end remote
begin remote
[b]name Hauppauge_350[/b]
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
# gap 200000
toggle_bit 2
begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes
end remote
|
|
| Top |
|
 |
|
pairajacks
|
Posted: Sun Jan 21, 2007 11:51 am |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
|
Can't figure out why this appears to be working, but no light blinking:
root@mythtv:/usr/local/bin# change_channel 200
channel changing 200
1. The change_channel script is unchanged from the instructions, and is in /usr/local/bin
2. I think my lircd.conf file (below) is correct and permissions wide open
root@mythtv:/etc# ls -alt lircd.conf
lrwxrwxrwx 1 root root 20 Jan 13 14:39 lircd.conf -> /etc/lirc/lircd.conf
3. The send_power_new makes the light blink
My lircd.conf file in /etc:
begin remote
name blaster
bits 32
flags RAW_CODES
eps 0
aeps 0
plead 0
gap 333333
repeat_bit 0
begin raw_codes
name 0
2149318656
name 1
2149318657
name 2
2149318658
name 3
2149318659
name 4
2149318660
name 5
2149318661
name 6
2149318662
name 7
2149318663
name 8
2149318664
name 9
2149318665
name POWER
2149318666
name CH_UP
2149318671
name CH_DOWN
2149318672
name MUTE
2149318673
name VOL_DOWN
2149318674
name CH_PREVIOUS
2149318675
name VOL_UP
2149318676
name DISPLAY
2149318677
name EXIT
2149318680
name GUIDE
2149318683
name SELECT
2149318686
name AV
2149318697
name ENTER
2149318699
name MENU
2149318703
name MUP
2149318704
name MDOWN
2149318705
name MLEFT
2149318706
name MRIGHT
2149318707
end raw_codes
end remote
begin remote
[b]name Hauppauge_350[/b]
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
# gap 200000
toggle_bit 2
begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes
end remote
|
|
| Top |
|
|
|
pairajacks
|
Posted: Sun Jan 21, 2007 11:52 am |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
|
Can't figure out why this appears to be working, but no light blinking:
root@mythtv:/usr/local/bin# change_channel 200
channel changing 200
1. The change_channel script is unchanged from the instructions, and is in /usr/local/bin
2. I think my lircd.conf file (below) is correct and permissions wide open
root@mythtv:/etc# ls -alt lircd.conf
lrwxrwxrwx 1 root root 20 Jan 13 14:39 lircd.conf -> /etc/lirc/lircd.conf
3. The send_power_new makes the light blink
My lircd.conf file in /etc:
[code]
begin remote
name blaster
bits 32
flags RAW_CODES
eps 0
aeps 0
plead 0
gap 333333
repeat_bit 0
begin raw_codes
name 0
2149318656
name 1
2149318657
name 2
2149318658
name 3
2149318659
name 4
2149318660
name 5
2149318661
name 6
2149318662
name 7
2149318663
name 8
2149318664
name 9
2149318665
name POWER
2149318666
name CH_UP
2149318671
name CH_DOWN
2149318672
name MUTE
2149318673
name VOL_DOWN
2149318674
name CH_PREVIOUS
2149318675
name VOL_UP
2149318676
name DISPLAY
2149318677
name EXIT
2149318680
name GUIDE
2149318683
name SELECT
2149318686
name AV
2149318697
name ENTER
2149318699
name MENU
2149318703
name MUP
2149318704
name MDOWN
2149318705
name MLEFT
2149318706
name MRIGHT
2149318707
end raw_codes
end remote
begin remote
[b]name Hauppauge_350[/b]
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
# gap 200000
toggle_bit 2
begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes
end remote
[/code]
|
|
| Top |
|
|
|
pairajacks
|
Posted: Sun Jan 21, 2007 11:54 am |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
|
Can't figure out why this appears to be working, but no light blinking:
root@mythtv:/usr/local/bin# change_channel 200
channel changing 200
1. The change_channel script is unchanged from the instructions, and is in /usr/local/bin
2. I think my lircd.conf file (below) is correct and permissions wide open
root@mythtv:/etc# ls -alt lircd.conf
lrwxrwxrwx 1 root root 20 Jan 13 14:39 lircd.conf -> /etc/lirc/lircd.conf
3. The send_power_new makes the light blink
My lircd.conf file in /etc:
[code]
begin remote
name blaster
bits 32
flags RAW_CODES
eps 0
aeps 0
plead 0
gap 333333
repeat_bit 0
begin raw_codes
name 0
2149318656
name 1
2149318657
name 2
2149318658
name 3
2149318659
name 4
2149318660
name 5
2149318661
name 6
2149318662
name 7
2149318663
name 8
2149318664
name 9
2149318665
name POWER
2149318666
name CH_UP
2149318671
name CH_DOWN
2149318672
name MUTE
2149318673
name VOL_DOWN
2149318674
name CH_PREVIOUS
2149318675
name VOL_UP
2149318676
name DISPLAY
2149318677
name EXIT
2149318680
name GUIDE
2149318683
name SELECT
2149318686
name AV
2149318697
name ENTER
2149318699
name MENU
2149318703
name MUP
2149318704
name MDOWN
2149318705
name MLEFT
2149318706
name MRIGHT
2149318707
end raw_codes
end remote
begin remote
[b]name Hauppauge_350[/b]
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
# gap 200000
toggle_bit 2
begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes
end remote
[/code]
|
|
| Top |
|
|
|
chunter2
|
Posted: Tue Jan 23, 2007 3:48 pm |
|
|
Joined: Mon May 02, 2005 9:00 am
Posts: 172
|
pairajacks wrote: Can't figure out why this appears to be working, but no light blinking:
root@mythtv:/usr/local/bin# change_channel 200
channel changing 200
1. The change_channel script is unchanged from the instructions, and is in /usr/local/bin
I can't seem to find the file you talk about in my R5E50 system. The one I use is Code: /usr/local/bin/change-channel-lirc.sh
You may need to create your own and I think you can find the code in the same post in this forum where you found the send_power_new file.
|
|
| Top |
|
|
|
pairajacks
|
Posted: Fri Jan 26, 2007 11:46 pm |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
|
Now I can't get the light to blink after sending the SEND_POWER_NEW script. This use to work. I know irw works still (can see commands from remote)
root@mythtv:/etc/lirc# send_power_new
(removed most of the output)
irsend: command failed: SEND_ONCE blaster 1_661_KEY_POWER
irsend: unknown command: "1_661_KEY_POWER"
irsend: command failed: SEND_ONCE blaster 1_662_KEY_POWER
irsend: unknown command: "1_662_KEY_POWER"
I tried restarting lircd with same result.
root@mythtv:/etc/lirc# /etc/init.d/lirc restart
Stopping lirc daemon: lircmd lircd.
Starting lirc daemon: lircd.
|
|
| Top |
|
|
|
chunter2
|
Posted: Sat Jan 27, 2007 8:08 am |
|
|
Joined: Mon May 02, 2005 9:00 am
Posts: 172
|
pairajacks wrote: Now I can't get the light to blink after sending the SEND_POWER_NEW script. This use to work.
To use your example, if the send_power_new script doesn't find an entry for 1_661_KEY_POWER in the lircd.conf script then you'll get that error. If you've already removed all the code for other set top boxes and edited your set top boxes section by removing the *_*_KEY_ then the send_power_new script won't work. The send_power_new script is only used to figure out which codes match up with your set top box. Once you've figured that out you don't need the script any more.
|
|
| Top |
|
|
|
pairajacks
|
Posted: Sat Feb 03, 2007 11:59 am |
|
|
Joined: Tue Oct 24, 2006 8:13 pm
Posts: 40
|
Thanks, that worked 
|
|
| Top |
|
|
View unanswered posts
View active topics
Linux 
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register