View unanswered posts    View active topics

Board index KnoppMyth Hardware

All times are UTC - 6 hours





Post new topic Reply to topic  Page 3 of 3
  [ 33 posts ] 
Go to page Previous  1, 2, 3
Print view Previous topic   Next topic  
Author Message
Search for:
roontoon
 Post subject:
PostPosted: Fri Aug 18, 2006 7:13 pm 
Offline
Joined: Mon Jul 17, 2006 12:59 pm
Posts: 45
Location: Tampa, Florida USA
tjc wrote:
Looks like your card is being detected properly now and you definitely needed the new drivers for that given the TCL M2523_5N_E chip.

Did you do the firmware update too? Did you turn the box off stone cold (unplug it to be sure) for at least 5 minutes to flush the old firmware?

Have you fiddled with your recording profiles at all? You might want to bump the Live TV profile to 640x480 @ 6000-8000kbps to see if that helps.


Yes I did do the firmware as per:

http://www.knoppmythwiki.org/index.php?page=CompileIvtv

I beleive I compleated each step but HEY I am a Luinx newbie so any thing could have gone wrong I wouldn't really know it.

Just rebooted as per the wiki.

10. Reboot the system. Do not skip this step!!!

Didn't say to do a cold shutdown. I will thy this in the morining. I previously did mess with the profiles but not the 6000-8000kkps, will also try that. If this doesn't work what else is there?

Also do you know when the new drivers will be incorporated into the KnoppMyth build?

_________________
MSI 661FM2-LSR SiS Motherboard
Intel Celeron D 340 2.93Ghz
1 gig DDR SDRAM
Seagate 320GB EIDE HD
NVIDIA GeForce FX 5500 256MB AGP w/DVI/TV-OUT
NEC ND-3550A 16X DVD Burner
Hauppauge PVR-150
nMEDIAPC 100BA Media Center Computer Case
Top
 Profile  
 
roontoon
 Post subject:
PostPosted: Sat Aug 19, 2006 11:37 am 
Offline
Joined: Mon Jul 17, 2006 12:59 pm
Posts: 45
Location: Tampa, Florida USA
OK I am about to give up. I obviously don't have a clue as to why this box is not working. Since my last post I have done the following:

1) Did a full reinstall of the software
2) Updated ivtv drivers and firmware as per suggested with full shutdown for 5 minutes.
3) Setup the prv-500 again.

Now no video at all. I go to view TV and the screen blinks and goes back to the menu.

4) Tried the last three steps again with a different motherboard (same type) and different CPU and go the same results.

I have spent sooooo much time without any results. Could this be a motherboard incompatability? At this point the only thing pluged into the motherboard it the PVR-500, RAM and the CPU. I took out my Nividia GeForce 5500 because I thought that might be causing problems.

I feel that I am pretty darn computer savy even though I am a linux newbie and I am frankly at a loss as to where to go from here. This has to be some sort of software issue or hardware/software incompatability. I have included the ivtv logs below.

Any ideas will be MORE than welcome.....

d ( longing for this thing to work )


Code:
Aug 19 13:01:41 mythtv kernel: ivtv:  ==================== START INIT IVTV ====================
Aug 19 13:01:41 mythtv kernel: ivtv:  version 0.4.6 (tagged release) loading
Aug 19 13:01:41 mythtv kernel: ivtv:  Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3
Aug 19 13:01:41 mythtv kernel: ivtv:  In case of problems please include the debug info between
Aug 19 13:01:41 mythtv kernel: ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
Aug 19 13:01:41 mythtv kernel: ivtv:  any module options, when mailing the ivtv-users mailinglist.
Aug 19 13:01:41 mythtv kernel: ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
Aug 19 13:01:41 mythtv kernel: ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 18 (level, low) -> IRQ 22
Aug 19 13:01:41 mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
Aug 19 13:01:41 mythtv kernel: tveeprom: Second (radio) tuner idx 101
Aug 19 13:01:41 mythtv kernel: tveeprom: ivtv version
Aug 19 13:01:41 mythtv kernel: tveeprom: Hauppauge: model = 23552, rev = D487, serial# = 9525414
Aug 19 13:01:41 mythtv kernel: tveeprom: tuner = Samsung TCPN 2221P30A (idx = 87, type = 68)
Aug 19 13:01:41 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Aug 19 13:01:41 mythtv kernel: tveeprom: audio processor = CX25843 (type = 25)
Aug 19 13:01:41 mythtv kernel: tveeprom: decoder processor = CX25843 (type = 1e)
Aug 19 13:01:41 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
Aug 19 13:01:42 mythtv kernel: tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #0
Aug 19 13:01:42 mythtv kernel: TEA5767 detected.
Aug 19 13:01:42 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
Aug 19 13:01:42 mythtv kernel: tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect
Aug 19 13:01:42 mythtv kernel: type set to 62 (Philips TEA5767HN FM Radio)
Aug 19 13:01:42 mythtv kernel: tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Aug 19 13:01:42 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
Aug 19 13:01:42 mythtv kernel: cx25840 0-0044: ivtv driver
Aug 19 13:01:42 mythtv kernel: cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
Aug 19 13:01:45 mythtv kernel: cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
Aug 19 13:01:45 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
Aug 19 13:01:45 mythtv kernel: wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
Aug 19 13:01:45 mythtv kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
Aug 19 13:01:46 mythtv kernel: ivtv0: This is the first unit of a PVR500
Aug 19 13:01:46 mythtv kernel: ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
Aug 19 13:01:46 mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
Aug 19 13:01:47 mythtv kernel: ivtv0: Encoder revision: 0x02050032
Aug 19 13:01:47 mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
Aug 19 13:01:47 mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
Aug 19 13:01:47 mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
Aug 19 13:01:47 mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
Aug 19 13:01:47 mythtv kernel: ivtv0: Create encoder radio stream
Aug 19 13:01:47 mythtv kernel: tuner: type set to 68 (Samsung TCPN 2221P30A) by ivtv i2c driver #0
Aug 19 13:01:48 mythtv kernel: ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
Aug 19 13:01:48 mythtv kernel: ivtv:  ======================  NEXT CARD  ======================
Aug 19 13:01:48 mythtv kernel: ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
Aug 19 13:01:48 mythtv kernel: ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 19 (level, low) -> IRQ 21
Aug 19 13:01:48 mythtv kernel: ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
Aug 19 13:01:48 mythtv kernel: tveeprom: Second (radio) tuner idx 101
Aug 19 13:01:48 mythtv kernel: tveeprom: ivtv version
Aug 19 13:01:48 mythtv kernel: tveeprom: Hauppauge: model = 23552, rev = D487, serial# = 9525414
Aug 19 13:01:48 mythtv kernel: tveeprom: tuner = Samsung TCPN 2221P30A (idx = 87, type = 68)
Aug 19 13:01:48 mythtv kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Aug 19 13:01:48 mythtv kernel: tveeprom: audio processor = CX25843 (type = 25)
Aug 19 13:01:48 mythtv kernel: tveeprom: decoder processor = CX25843 (type = 1e)
Aug 19 13:01:48 mythtv kernel: ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
Aug 19 13:01:48 mythtv kernel: tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
Aug 19 13:01:48 mythtv kernel: ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
Aug 19 13:01:48 mythtv kernel: cx25840 1-0044: ivtv driver
Aug 19 13:01:48 mythtv kernel: cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
Aug 19 13:01:51 mythtv kernel: cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
Aug 19 13:01:51 mythtv kernel: ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
Aug 19 13:01:51 mythtv kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
Aug 19 13:01:51 mythtv kernel: ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
Aug 19 13:01:51 mythtv kernel: ivtv1: This is the second unit of a PVR500
Aug 19 13:01:51 mythtv kernel: ivtv1: Correcting tveeprom data: no radio present on second unit
Aug 19 13:01:52 mythtv kernel: ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
Aug 19 13:01:53 mythtv kernel: ivtv1: Encoder revision: 0x02050032
Aug 19 13:01:53 mythtv kernel: ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
Aug 19 13:01:53 mythtv kernel: ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
Aug 19 13:01:53 mythtv kernel: ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
Aug 19 13:01:53 mythtv kernel: ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
Aug 19 13:01:53 mythtv kernel: tuner: type set to 68 (Samsung TCPN 2221P30A) by ivtv i2c driver #1
Aug 19 13:01:53 mythtv kernel: ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
Aug 19 13:01:53 mythtv kernel: ivtv:  ====================  END INIT IVTV  ====================

_________________
MSI 661FM2-LSR SiS Motherboard
Intel Celeron D 340 2.93Ghz
1 gig DDR SDRAM
Seagate 320GB EIDE HD
NVIDIA GeForce FX 5500 256MB AGP w/DVI/TV-OUT
NEC ND-3550A 16X DVD Burner
Hauppauge PVR-150
nMEDIAPC 100BA Media Center Computer Case
Top
 Profile  
 
roontoon
 Post subject:
PostPosted: Sun Aug 27, 2006 6:16 pm 
Offline
Joined: Mon Jul 17, 2006 12:59 pm
Posts: 45
Location: Tampa, Florida USA
tjc,

Thanks for your help. I got the video working. Not sure what I did different or I would write it up for others. This last time I totally broke down all of the hardware and did a complete reassembly and reinstalled knoppmyth ( for the millionth time ) and vola it worked. It had some interference and I set the screen size to 720x480 and it cleared it up.

d

_________________
MSI 661FM2-LSR SiS Motherboard
Intel Celeron D 340 2.93Ghz
1 gig DDR SDRAM
Seagate 320GB EIDE HD
NVIDIA GeForce FX 5500 256MB AGP w/DVI/TV-OUT
NEC ND-3550A 16X DVD Burner
Hauppauge PVR-150
nMEDIAPC 100BA Media Center Computer Case
Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 3 of 3
  [ 33 posts ] 
Go to page Previous  1, 2, 3


Board index KnoppMyth Hardware

All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 23 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu