I was on an older version of Knoppmyth, and for the most part it was running great. I ended up having to move and reset all my channels and the like, so I decided I may as well do an upgrade to take advantage of all the bug fixes and the like. Unfortunatly, after upgrading I can't watch live TV, and if I try the backend seems to crash, or at least the frontend can't establish a connection. All I see is black for about 15 seconds, then it kicks me back out to the main menu. If I try to watch recordings before that, I can, and they play fine.

I've tried installing the firmware again and a couple of other things, but nothing seems to be working right. Anyone have any suggestions as to how to fix this problem? Any help is greatly appreciated!!!

_________________
Nerd is not a four-letter word. It's a six-figure income.

See the Wiki page on http://www.knoppmythwiki.org/index.php?page=CheckingLogFiles, follow the instructions for how get the ivtv info from dmesg, and post it here.

Here is the output of "sed -n '/= START INIT IVTV/,/= END INIT IVTV/p' </var/log/dmesg | more"

Thanks!


ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 17 (level, low) -> IRQ 19
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #0
TEA5767 detected.
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect
type set to 62 (Philips TEA5767HN FM Radio)
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 2995726
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
ivtv0: This is the first unit of a PVR500
cx25840: Unknown parameter `i2c_enable'
ivtv0: Failed to load module cx25840
ivtv0 warning: i2c client addr: 0x44 not found for command 0x400464c9!
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046403!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046404!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x4004646e!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046403!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x80287610!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40287611!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046406!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x4004760f!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046406!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x80287610!
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40287611!
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 20
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 2995726
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
cx25840: Unknown parameter `i2c_enable'
ivtv1: Failed to load module cx25840
ivtv1 warning: i2c client addr: 0x44 not found for command 0x400464c9!
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046403!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046404!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x4004646e!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046403!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x80287610!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40287611!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046406!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x4004760f!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046406!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x80287610!
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40287611!
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================

_________________
Nerd is not a four-letter word. It's a six-figure income.

bump Anyone?

_________________
Nerd is not a four-letter word. It's a six-figure income.

Did you check the link that tjc posted? Did you check the backend log?

_________________
cesman

When the source is open, the possibilities are endless!