View unanswered posts    View active topics

Board index Linux MythTV

All times are UTC - 6 hours





Post new topic Reply to topic  Page 1 of 2
  [ 20 posts ] 
Go to page 1, 2  Next
Print view Previous topic   Next topic  
Author Message
Search for:
rkhanso
PostPosted: Mon Nov 07, 2005 9:52 pm 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
I have Time Warner cable. A PVR-350 card that can tune in channels 2-13 come in fine, 14-20 are snow, 21-36 come in fine, then 37-60 are snow and lastly, 60+ are OK.

Many (not all) of the block of 14-20 are local cable access channels, if that makes a difference.

Is there some settings I can change? Is this just not going to work with my cable provider?

I don't have digital cable, nor any cable box/converter. All the channels come in fine on the TV directly, just not through KnoppMyth, and only the blocks of channels listed above have trouble (14-20 and 37-60)

Thanks for any help you can provide.
Top
 Profile  
 
Xsecrets
 Post subject:
PostPosted: Mon Nov 07, 2005 10:03 pm 
Offline
Joined: Mon Oct 06, 2003 10:38 am
Posts: 4978
Location: Nashville, TN
have you tried swapping back and forth between uscable and uscable-hrc in mythtv-setup?

_________________
Have a question search the forum and have a look at the KnoppMythWiki.

Xsecrets
Top
 Profile  
 
tjc
 Post subject:
PostPosted: Mon Nov 07, 2005 10:04 pm 
Offline
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location: Arlington, MA
Search for a recent thread (something about no sound on some channels) which includes posts by me related to frequency charts. The charts might reveal a pattern. What frequency set did you select in mythtv-setup? us-bcast? us-cable? us-cable-hrc? There really should be a 4th one us-cable-irc but you have to use fine tuning for that.
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Mon Nov 07, 2005 10:27 pm 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
I changed it to US-Cable and there's no change, still snow

I changed it to US-Cable-HRC and there's no change, still snow

I'll try fine-tuning...
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Mon Nov 07, 2005 10:56 pm 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
I picked out 1 channel (one I was hoping to record tonight) and tried various numbers in the fine-tuning column on the web page.

Is there any rhyme/reason for choosing numbers to enter here?

I tried 125 and 107 as has been suggested in other posts to no avail. I've tried numbers from 0 to 600 by 50's and could see some pattern change to the snow (black bands, squiggly black bars, etc) - there was nothing that resembled a valid TV picture.

Are there guidelines for fine-tuning numbers or other things I need to try or check or post out of my config?
Top
 Profile  
 
tjc
 Post subject:
PostPosted: Mon Nov 07, 2005 11:05 pm 
Offline
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location: Arlington, MA
What do these print?
Code:
mysql mythconverg -e "select data from settings where value = 'FreqTable'"
mysql mythconverg -e "select freqtable from videosource"
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Tue Nov 08, 2005 12:47 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
root@pvr:/home/mythtv# mysql mythconverg -e "select data from settings where value = 'FreqTable'"
+----------+
| data |
+----------+
| us-cable |
+----------+

and:

root@pvr:/home/mythtv# mysql mythconverg -e "select freqtable from videosource"
+-----------+
| freqtable |
+-----------+
| default |
+-----------+
Top
 Profile  
 
EvilTwin
 Post subject:
PostPosted: Tue Nov 08, 2005 7:43 am 
Offline
Joined: Tue Nov 08, 2005 7:31 am
Posts: 195
Location: Secret Lair
Searching for "time warner cable" shows this: http://mysettopbox.tv/phpBB2/viewtopic.php?t=6345&highlight=warner+cable
So you may be SOL because your cable company is run by dorks. Just for giggles try the us-bcast setting.
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Tue Nov 08, 2005 8:01 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
somehow a double-post. see next post...


Last edited by rkhanso on Tue Nov 08, 2005 8:06 am, edited 1 time in total.
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Tue Nov 08, 2005 8:04 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
well, I did a suggestion in that other post and see a possible problem?
dmesg | grep ivtv
Code:
root@pvr:/home/mythtv# dmesg | grep ivtv | more
ivtv0 warning: Mailbox[0] 0x00000008 flags 0x00000003
ivtv0 warning: Mailbox[1] 0x00000008 flags 0x00000003
ivtv0 warning: Firmware UNRESPONSIVE when trying cmd 0x00000001!!!
ivtv0 warning: Failed to start decoding for stream 5
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000015 with result 0xfffffff0
ivtv0 warning: DEC: couldn't read clock
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000019 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000017 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x0000001a with result 0xfffffff0
ivtv0 warning: COULDN'T INITIALIZE DECODER SOURCE -16
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000001 with result 0xfffffff0
ivtv0 warning: Failed to start decoding for stream 5
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000015 with result 0xfffffff0
ivtv0 warning: DEC: couldn't read clock
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000019 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000017 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x0000001a with result 0xfffffff0
ivtv0 warning: COULDN'T INITIALIZE DECODER SOURCE -16
ivtv0 warning: No Free Mailbox for cmd 0x00000001 after 100 tries!
ivtv0 warning: Mailbox[0] 0x00000008 flags 0x00000003
ivtv0 warning: Mailbox[1] 0x00000008 flags 0x00000003
ivtv0 warning: Firmware UNRESPONSIVE when trying cmd 0x00000001!!!
ivtv0 warning: Failed to start decoding for stream 5
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000015 with result 0xfffffff0
ivtv0 warning: DEC: couldn't read clock
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000019 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000017 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x0000001a with result 0xfffffff0
ivtv0 warning: COULDN'T INITIALIZE DECODER SOURCE -16
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000001 with result 0xfffffff0
ivtv0 warning: Failed to start decoding for stream 5
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000015 with result 0xfffffff0
ivtv0 warning: DEC: couldn't read clock
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000019 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x00000017 with result 0xfffffff0
ivtv0 warning: 1000 ms time out waiting for firmware
ivtv0 warning: Failed api call 0x0000001a with result 0xfffffff0
ivtv0 warning: COULDN'T INITIALIZE DECODER SOURCE -16
ivtv0 warning: No Free Mailbox for cmd 0x00000001 after 100 tries!
ivtv0 warning: Mailbox[0] 0x00000008 flags 0x00000003

Here's my ivtv config:
Code:
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.4.0 (tagged release) loading
ivtv:  Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
ivtv:  In case of problems please include the debug info
ivtv:  between the START INIT IVTV and END INIT IVTV lines when
ivtv:  mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (iTVC15 based)
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ
 11
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G)
 no-thread mode
msp34xx: $Id$ compiled on: Oct  9 2005 22:52:16
ivtv0: i2c attach to card #0 ok [client=MSP3448W-A2, addr=40]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 7875278
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: loading /lib/modules/ivtv-fw-dec.bin
ivtv0: Encoder revision: 0x02040011
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loading /lib/modules/ivtv_init_mpeg.bin
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
spurious 8259A interrupt: IRQ7.
ivtv0: Initialized WinTV PVR 350, card #0
ivtv:  ====================  END INIT IVTV  ====================
any changes needed?
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Thu Nov 10, 2005 1:07 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
I tried the Broadcast setting in the mythtv-setup and I had even more channels that were snow, plus a KnoppMyth system lockup.

I'm running out of options...

I haven't heard back from Time Warner what frequency standard they use.
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Tue Nov 22, 2005 1:39 pm 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
Shall I try various tuner types? Any other ideas? Still haven't figured out the blocks of channels with snow problem yet.

current data:
Code:
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.4.0 (tagged release) loading
ivtv:  Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
ivtv:  In case of problems please include the debug info
ivtv:  between the START INIT IVTV and END INIT IVTV lines when
ivtv:  mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (iTVC15 based)
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Oct  9 2005 22:52:16
ivtv0: i2c attach to card #0 ok [client=MSP3448W-A2, addr=40]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 7875278
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: loading /lib/modules/ivtv-fw-dec.bin
ivtv0: Encoder revision: 0x02040011
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loading /lib/modules/ivtv_init_mpeg.bin
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
spurious 8259A interrupt: IRQ7.
ivtv0: Initialized WinTV PVR 350, card #0
ivtv:  ====================  END INIT IVTV  ====================
Top
 Profile  
 
tjc
 Post subject:
PostPosted: Tue Nov 22, 2005 7:45 pm 
Offline
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location: Arlington, MA
Frankly I'm starting to think it's the cable system. Have you tried the channel scanner under mythtv-setup? It's under "Channel Editor".

OBTW - Backup your DB first!
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Wed Nov 23, 2005 8:13 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
tjc - I tried your suggestion...

When I had Myth scan for channels, it skipped right over the ones that have snow - the same 2 blocks of channels as I mentioned before.

Additionally, I tried both US-Cable and US-Cable HRC options and then scanned for channels. Same situation using both options.

Do I need to change tuner settings? Any other things to try?
Top
 Profile  
 
rkhanso
 Post subject:
PostPosted: Wed Nov 23, 2005 8:33 am 
Offline
Joined: Thu May 12, 2005 9:45 pm
Posts: 95
Location: Minneapolis area
OK - I think I've found something to investigate.

When looking at MythWeb and the Channels (I was going to fine-tune)

I see no valid-looking frequencies for the snowy channels.

Image
See image and look at column 6. The channels I can tune in show frequencies like 294000 and the ones I can't tune in show a frequency that is just simply the channel number.

Additionally - the channels I can tune in are shown in column 5 as just listing the channel number while the ones I can't tune in actually have the channel ID shown.

I'm sure there's a simple correction for this problem.....I hope.

Can someone help?
Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 20 posts ] 
Go to page 1, 2  Next


Board index Linux MythTV

All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 4 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu