View unanswered posts    View active topics

Board index KnoppMyth Hardware

All times are UTC - 6 hours





Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
Zepalesque
PostPosted: Sat Dec 03, 2005 5:11 pm 
Offline
Joined: Sat Dec 03, 2005 5:04 pm
Posts: 12
Has anyone seen this problem before?

I have a PVR-350 and have tweaked just about everything I care about to work - expect that I cannot control the volume using the keyboard or remote control. I do get sound and can control the volume using the television's remote.

Just in case the information is relevant, here's my output from lspci:
Code:
0000:00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory C
ontroller Hub (rev 02)
0000:00:01.0 PCI bridge: Intel Corp. 82815 815 Chipset AGP Bridge (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 02)
0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 02)
0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 02)
0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 02)
0000:02:09.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
 78)
0000:02:0a.0 Multimedia video controller: Internext Compression Inc iTVC15 MPEG-
2 Encoder (rev 01)
0000:02:0b.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 09)
0000:02:0c.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Ra
deon 7000/VE]

Thanks!
Top
 Profile  
 
stevepugh
 Post subject:
PostPosted: Sat Dec 03, 2005 6:25 pm 
Offline
Joined: Fri Feb 18, 2005 3:20 pm
Posts: 22
Location: Los Angeles, CA
If you're using the PVR-350 for your audio output, do you have it looped through your soundcard properly?

If you don't, and are piping it directly into your speakers/audio gear, then you won't be able to use Myth controls to adjust volume. There is a checkbox for using the PVR-350's audio out instead of loop-through in Setup/Playback somewhere...

Best,
Steve

_________________
-Steve
Top
 Profile  
 
ryanpatterson
 Post subject:
PostPosted: Sat Dec 03, 2005 8:01 pm 
Offline
Joined: Fri Aug 26, 2005 9:54 pm
Posts: 617
The audio out from the pvr-350 is a linelevel out. It can not be controled by mythtv. It is always at 100%.

However stevepugh just posted if you loop the audio signal through your line-in on your soundcard mythtv can control the level. This will also allow you to get sould from mplayer or xine.
Top
 Profile  
 
Zepalesque
 Post subject: Thanks !
PostPosted: Sun Dec 04, 2005 2:05 am 
Offline
Joined: Sat Dec 03, 2005 5:04 pm
Posts: 12
Thanks for the info, I appreciate it. Looks like I have to go shopping for a cable tomorrow.
Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 


Board index KnoppMyth Hardware

All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 13 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu