I have been running Knoppmyth since the release of R5C7 with all functions working so a big thank you to Cecil and everyone who helps in the devlopment of Knoppmyth.
Ok on to my problem with my Hauppauge Remote after upgrade to R5D1, having followed the sticky from tjc all functions worked OK except the Number keys on the remote.
Exiting the Frontend and opening a terminal window and running irw shows all keys working except number keys. Closing irw and pressing the number keys and they show !!
Manually restoring /etc/lirc/hardware.conf and /etc/lirc/lirc.conf restarting lirc gives the same result.
I have tried a clean install to a spare hard drive of R5D1 and reinstated all the lirc conf files, again the number keys will not work.
I have also tried a clean install of R5C7 reinstated all the lirc conf files and the number keys work OK. Upgraded this install to R5D1 and number keys stop working, all other keys are fine.
Any help or pointers where to start fault finding from here appreciated.

_________________
MSI K8 Neo AMD 3200 Sempron 1GB RAM Seagate 300GB HD 2* Nova Ts

Have you tried running lirc_reconfig.sh?

_________________
cesman

When the source is open, the possibilities are endless!

Thanks for the reply Cesman, yes I have tried lirc_reconfig.sh, still no go.
I have moved one of my Nova Ts to another more accessible box and tried the following:-
Clean install of R5C7, SSH from Laptop and Edit /etc/lirc/hardware.conf and /etc/lirc/lircd.conf as follows,

# /etc/lirc/hardware.conf
# Arguments which will be used when launching lircd
LIRCD_ARGS=""

#Don't start lircmd even if there seems to be a good config file
START_LIRCMD=false

#Try to load appropriate kernel modules
LOAD_MODULES=true

# Run "lircd --driver=help" for a list of supported drivers.
DRIVER="default"
# If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0 will be
# automatically used instead
# DEVICE="/dev/lirc"
# MODULES="lirc_dev lirc_i2c"
DEVICE="/dev/input/event2"
DRIVER="dev/input"

# /etc/lirc/lircd.conf
# Please make this file available to others
# by sending it to <lirc@bartelmus.de>
#
# this config file was automatically generated
# using lirc-0.7.2pre1(devinput) on Sat Jun 18 13:18:13 2005
#
# contributed by Paul Grigg (mad_paddler)
#
# brand: cx88.cfg
# model no. of remote control: Hauppauge silver remote with
# Connexant chipset Nova-T
# devices being controlled by this remote:
#

begin remote

name cx88.cfg
bits 16
eps 30
aeps 100

one 0 0
zero 0 0
pre_data_bits 16
pre_data 0x8001
gap 132900
toggle_bit 0


begin codes
Go 0x0161
Power 0x0074
TV 0x0179
VIDEOS 0x0189
MUSIC 0x0188
PICTURES 0x016F
GUIDE 0x016D
RADIO 0x0181
UP 0x0067
DOWN 0x006C
LEFT 0x0069
RIGHT 0x006A
OK 0x001C
BACK/EXIT 0x00AE
Menu/i 0x008B
VOL+ 0x0073
VOL- 0x0072
CH+ 0x0192
CH- 0x0193
Prev.Ch 0x019C
MUTE 0x0071
RECORD 0x00A7
STOP 0x0080
Rewind 0x00A8
PLAY 0x00CF
Forward 0x00D0
Replay/SkipBackward 0x00A5
PAUSE 0x0077
SkipForward 0x00A3
1 0x004F
2 0x0050
3 0x0051
4 0x004B
5 0x004C
6 0x004D
7 0x0047
8 0x0048
9 0x0049
0 0x0052
Asterix 0x0184
# 0x0172
RED 0x018E
GREEN 0x018F
YELLOW 0x0190
BLUE 0x0191
end codes

end remote


Restart Lirc
Run IRW in Terminal Window and all Remote keys show in window with the correct description from lircd.conf .
I then did a clean install of R5D1 repeated all of above, running irw, this time all keys show in window EXCEPT number keys.
Looking through the changlog I can not see any changes in Lirc between the versions so now I am stumped, not to sure where to look next.
Again any help appreciated.

_________________
MSI K8 Neo AMD 3200 Sempron 1GB RAM Seagate 300GB HD 2* Nova Ts

I am having this issue as well
remote was working in R5C7 but not anymore under R5D1
I have the pvr350
not really sure where to start here

Which remote you guys choosing from the reconfig lirc script? Try the "dog bone" remote should be pretty compatible with most of the newer Hauppuage remotes.

Well that worked
used dog bone option
I'm sure I tried that option before but this time I restarted the frontend.

Thanks for making me try it again

Ok, so still unable to get Numbers Keys working in R5D1, because nobody else appears to be having this problem I am starting to assume that it must be something that I am doing/not doing, so I will go through all the steps that I have taken so far in the hope that someone will spot what is wrong.
The Test Hardware (but all steps have also been tried on my regular Knoppmyth box)
Gigabyte Intel 845 M/Board, Celeron 2.7Gh, 512MB RAM, Nvidia FX5200,
Hauppagge Nova T (9002) A415 OH/S1-4 On battery cover.

The hardware.conf and lircr.conf files



Clean Install R5C7, Edit hardware.conf and lircr.conf, reboot to be on safe side!, exit frontend, ALT X to terminal, enter irw, and press keys on remote and ALL keys repeat on screen.

Clean Install R5D1, Edit hardware.conf and lircr.conf, reboot to be on safe side!, exit frontend, ALT X to terminal, enter irw, and press keys on remote and all keys repeat on screen EXCEPT NUMBER keys.
If I try the upgrade path the same thing happens.
I have tried the all the hauppauge options from the reconfig lirc script to no avail.
I have even tried a clean install of Ubuntu 5.1, installed LIRC, edit the files to as above and all the keys work. It is only in R5D1 that I am having this problem.
Hoping someone can come up with an answer or suggestions to this, else I am going to have to stick with R5C7 until the next release.
Thanks in advance.

_________________
MSI K8 Neo AMD 3200 Sempron 1GB RAM Seagate 300GB HD 2* Nova Ts

Add on to my previous post.
Just noticed that in R5C7 in a terminal window without running irw,pressing the remote number keys produce:-
1 = nothing
2 = ~
3 = ~ and beep from speaker
4 = backspace
5 = beep from speaker
6 = beep from speaker
7 = backspace
8 = repeats last command
9 = ~
0 = ~

R5D1 in a terminal window without running irw, pressing the remote number keys produce:-
1 = 1
2 = 2
3 = 3
And so on.

Not to sure what this means, hoping some does !

_________________
MSI K8 Neo AMD 3200 Sempron 1GB RAM Seagate 300GB HD 2* Nova Ts

tizwoz

I'm having the same problem. I had it working yesterday with the dog bone option. Power Failure. Now nothing. I tried all the remotes again. dog bone,silver etc. nothing.

I have the exact same remote as yours.

Hey guys,

I expect your problem is related to the one I was having check out my post - http://mysettopbox.tv/phpBB2/viewtopic. ... 1585#71585.

Don't forget to follow the other walkthrough through first.