LinHES Forums • View topic - upgraded FE/SBE to R5F27 PVR-150 unavailable in MBE-SOLVED!

Board index KnoppMyth General

All times are UTC - 6 hours

upgraded FE/SBE to R5F27 PVR-150 unavailable in MBE-SOLVED!

Page 1 of 1

[ 3 posts ]

Print view

Previous topic Next topic

Author

Message

bigbro

Post subject: upgraded FE/SBE to R5F27 PVR-150 unavailable in MBE-SOLVED!

Posted: Sun Sep 16, 2007 6:22 pm

Joined: Sat Dec 24, 2005 11:33 am

Posts: 400

Location: Kitsap Peninsula, Wa., United States

Changed Subject to help searchers
Deleted some of the post for another thread.
Solution is in last post.
Mostly this went well.

This one is an older Gigabyte - GA 7Zmmh mobo with an Athlon 2200+

it only has one PVR 150 but is my primary Front end box

I deleted and resetup the pvr 150 like 3 times now and I get that it is unavailable in the System information and everything defaults to Tuner 1 in the MBE.

Here is what appears to be my Tuner card setup (IVTV) from the syslog:

Code:

Sep 16 17:01:36 mythtv_sbe kernel: Linux video capture interface: v2.00
Sep 16 17:01:36 mythtv_sbe kernel: ivtv:  Start initialization, version 1.1.0
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Initializing card #0
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Autodetected Hauppauge card (cx23416 based)
Sep 16 17:01:36 mythtv_sbe kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Sep 16 17:01:36 mythtv_sbe kernel: PCI: Found IRQ 10 for device 0000:00:0a.0
Sep 16 17:01:36 mythtv_sbe kernel: PCI: Sharing IRQ 10 with 0000:00:0e.0
Sep 16 17:01:36 mythtv_sbe kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: Hauppauge model 26032, rev C199, serial# 8296927
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: audio processor is CX25841 (idx 35)
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: decoder processor is CX25841 (idx 28)
Sep 16 17:01:36 mythtv_sbe kernel: tveeprom 1-0050: has no radio, has IR receiver, has IR transmitter
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Autodetected Hauppauge WinTV PVR-150
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Reopen i2c bus for IR-blaster support
Sep 16 17:01:36 mythtv_sbe kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Sep 16 17:01:36 mythtv_sbe kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Sep 16 17:01:36 mythtv_sbe kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Sep 16 17:01:36 mythtv_sbe kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Sep 16 17:01:36 mythtv_sbe kernel: cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
Sep 16 17:01:36 mythtv_sbe kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
Sep 16 17:01:36 mythtv_sbe kernel: tuner-simple 1-0061: type set to 50 (TCL 2002N)
Sep 16 17:01:36 mythtv_sbe kernel: tuner 1-0061: type set to TCL 2002N
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Registered device video0 for encoder MPG (4096 kB)
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Registered device video32 for encoder YUV (2048 kB)
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Registered device video24 for encoder PCM (320 kB)
Sep 16 17:01:36 mythtv_sbe kernel: ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
Sep 16 17:01:36 mythtv_sbe kernel: ivtv:  End initialization
Sep 16 17:01:36 mythtv_sbe kernel: PCI: Found IRQ 10 for device 0000:00:0e.0
Sep 16 17:01:36 mythtv_sbe kernel: PCI: Sharing IRQ 10 with 0000:00:0a.0
Sep 16 17:01:36 mythtv_sbe kernel: Adding 1953496k swap on /dev/hda2.  Priority:-1 extents:1 across:1953496k
Sep 16 17:01:36 mythtv_sbe kernel: EXT3 FS on hda1, internal journal
Sep 16 17:01:36 mythtv_sbe kernel: bttv: driver version 0.9.17 loaded
Sep 16 17:01:36 mythtv_sbe kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture
Sep 16 17:01:36 mythtv_sbe kernel: bt878: AUDIO driver version 0.0.0 loaded
Sep 16 17:01:36 mythtv_sbe kernel: Non-volatile memory driver v1.2
Sep 16 17:01:36 mythtv_sbe kernel: saa7130/34: v4l2 driver version 0.2.14 loaded
Sep 16 17:01:36 mythtv_sbe kernel: cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
Sep 16 17:01:36 mythtv_sbe kernel: cx88/2: cx2388x dvb driver version 0.0.6 loaded
Sep 16 17:01:36 mythtv_sbe kernel: cx88/2: registering cx8802 driver, type: dvb access: shared

If there is something else you can recommend I look at or post let me know. I may try a reinstall of this system, as I don't see any answers or similar symptoms to this in the forum.

Regards.

Last edited by bigbro on Tue Sep 18, 2007 9:32 pm, edited 2 times in total.

Top

bigbro

Post subject:

Posted: Mon Sep 17, 2007 9:06 pm

Joined: Sat Dec 24, 2005 11:33 am

Posts: 400

Location: Kitsap Peninsula, Wa., United States

Update and a Bump.
I believe I am onto the root cause of the problem..

I upgraded my second FE/SBE
it carries a PVR 500 for tuners.

First I built the system as a standalone. MBE/FE combination the Tuners are recognized and it is able to record and playback those files.
Everything works fine.
It is an Abit NF7-s with a Duron 1800 and 512 megs of Ram but a small hard drive.

Next I converted it to the FE/SBE it was originally.

When i look in system settings it comes as Tuner 5 and 6 but they are not available
Once my MBE finishes recording one of the wifes shows I will go into the MySQL Tuner cards and see what I can find in there.

It isn't a must but it would be nice if I could get rid of the extra tuner numbers and get back to 1-4 while I fix this.

It would seem that these SBE are only partially being accepted by the MBE database.

Thoughts? Anything else I can provide?

I will keep puttering myself on this.

Top

bigbro

Post subject: The Solution

Posted: Tue Sep 18, 2007 9:50 pm

Joined: Sat Dec 24, 2005 11:33 am

Posts: 400

Location: Kitsap Peninsula, Wa., United States

Mostly it seems it may have been my fault.

I remembered some quirks when I first built the 3 systems how it was finicky in setting up the 3 capture cards/4 tuners across the 3 boxes.

I opened the MBE/FE and the primary SBE/FE in two VNC windows.
Next I exited to the desktops on both of them and shutdown (Alt-2) on both Backends . Don't ask me why but it seems there are two backends running although everything defaults to one location.

I ram Mythtv-Setup (ALT-S) on both machines and deleted "All Capture Cards" in both machines starting with the MBE then the SBE.

Now I powered down, waited 5 min. then restarted both machines MBE then SBE.

Returned to the Desktop, then I stopped the Backends (Alt-2) again and started Mythtv-Setup (Alt-S) on both of them.

On the MBE first I added the capture card, checked that the source was still there and then Connected the source to the Card Input (S-video) in my case. I exited that Mythtv-setup, and acknowledged the Master backend warning about mythfilldatabase.

Next the SBE I added the capture card, checked the Source was there, and then connected the source to the Card Input (S-Video). I exited mythtv-setup and acknowledged the the Master backend warning about mythfilldatabase.

Now I returned to the MBE window and opened a terminal (Alt-x) and ran mythfilldatabase.

Once mythfilldatabase completed on the MBE I closed the terminal. Then I started the Backend (Alt-3). Next I brought up the Frontend (Alt-M) waited a couple of minutes (recommended in the Hints for other reasons)
Checked the System Status Tuner 1 was there and Tuner 2 was unavialable.

I went to my VNC window for the SBE and started the backend (Alt-3) waited a couple of minutes, then brought up the Frontend (Alt-M).

I went back to the MBE and checked System Status and after the second refresh of the screen Tuner 2 was now available and so was Tuner 1.

Woohoo!

I have restarted both machines a couple of times and even done a little recording or watch live tv on Tuner 2. It works from both the MBE/FE and the SBE/FE.

I don't know exactly why it took these specific steps or if it was that restart in the middle with no cards but hey it worked and now the WAF is climbing again......

I guess an old dog can learn new tricks!

Top

Page 1 of 1

[ 3 posts ]

Board index KnoppMyth General

All times are UTC - 6 hours

Who is online

Users browsing this forum: No registered users and 19 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum